606215

Einhell TE-ID 1050-1 CE Manual

17
Zoom out
Zoom in
Previous page
1/108
Next page
GB
- 17 -
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making adjust-
ments to the equipment.
5.1. Fitting the additional handle (Fig. 2-3/
Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do
not use the tool without the additional handle.
The additional handle (8) is secured to the ham-
mer drill by a clamp. During the handle clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
•
The supplied additional handle (8) must
first be fitted. To do this, the clamp must be
opened by turning the handle until it is wide
enough for the additional handle to be slid
over the chuck (1) and on to the hammer drill.
•
After you have positioned the additional
handle (8), turn it to the most comfortable
working position for you.
•
Now turn the handle in the opposite direction
again until the additional handle is secure.
•
The additional handle (8) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop
(Fig. 4/Item 2)
•
Undo the thumb screw (a) on the additional
handle (8) and insert the depth stop (2) in the
hole of the additional handle.
•
Set the depth stop and retighten the thumb
screw.
•
Now drill the hole until the depth stop touches
the workpiece.
5.3 Fitting the drill bit (Fig. 5)
Always pull the power plug before making adjust-
ments to the equipment.
•
Release the depth stop as described in 5.2
and push it towards the additional handle.
This provides free access to the chuck (1).
•
This hammer drill is fitted with a keyless
chuck (1).
•
Open the chuck (1). The drill bit opening must
be large enough to fit the drill bit into.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Close the chuck (1). Check that the drill bit is
secure in the chuck (1).
•
Check at regular intervals that the drill bit or
tool is secure (pull the mains plug).
6. Operation
6.1 ON/OFF switch (Fig. 6/Item 5)
•
First fit a suitable drill bit into the tool (see
5.3).
•
Connect the mains plug to a suitable socket.
•
Position the drill in the position you wish to
drill.
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
To switch off :
Press the ON/OFF switch (5) briefl y.
6.2 Adjusting the speed (Fig. 6/Item 5)
You can infi nitely vary the speed whilst using the
tool.
•
Select the speed by applying a greater or les-
ser pressure to the ON/OFF switch (5).
•
Select the correct speed: The most suitable
speed depends on the workpiece, the type of
use and the drill bit used.
•
Low pressure on the ON/OFF switch (5): Lo-
wer speed (suitable for: small screws and soft
materials)
•
Greater pressure on the ON/OFF switch (5):
Higher speed (suitable for large/long screws
and hard materials)
Tip: Start drilling holes at low speed. Then increa-
se the speed in stages.
Benefi ts:
•
The drill bit is easier to control when starting
the hole and will not slide away.
•
You avoid drilling messy holes (for example
in tiles).
6.3 Preselecting the speed (Fig. 7/Item 6)
The speed controller (6) enables you to defi ne the
maximum speed.
•
Set the speed controller (6) to the required
position.
•
With the On/Off switch (5) pressed right in,
Anleitung_TE_ID_1050_1_CE_SPK7.indb 17Anleitung_TE_ID_1050_1_CE_SPK7.indb 17 25.11.13 13:0525.11.13 13:05
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell TE-ID 1050-1 CE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TE-ID 1050-1 CE in the language / languages: English, German, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info