605669
16
Zoom out
Zoom in
Previous page
1/86
Next page
GB
- 16 -
Switch position 2:
2nd setting – 50-550°C / 250 liters/min.
Switch position 3:
3rd setting – 50-550°C / 500 liters/min.
Note:
The temperature can only be adjusted in setting 2
and 3.. You can do this by turning the temperature
setting wheel (6) variably back and forth between
positions 1 – 9. The LED display (5) shows by 6
switch positions the temperature level that applies
at the moment.
In switch position 1 the LED display (5) goes o
completely.
Note:
Switch position 1 is a cold air setting at 50 °C.
This is when the hot air gun needs to be cooled
down faster so that you can change the nozzles
more quickly and avoid the danger of burns.
6.2 Possible uses for the hot air pistol:
Removal of paint and lacquer. Attention!
Hazardous or poisonous gasses may be
produced while removing paint or lac-
quer. Be sure to provide adequate venti-
lation.
Removal of stickers and decorations.
Loosening of rusted or tightly fastened nuts
and metal screws.
Thawing of frozen pipes, door locks, etc.
Attention: no not attempt to thaw plastic or
synthetic pipes.
Accentuation of natural wood grains before
staining or lacqueing.
Shrinkage of PVC packaging foils and insula-
tion tubes.
Waxing and de-waxing of skis.
Stationary use (see Fig. 4)
Danger! Intensive heating means a higher
risk of re and explosion! Ensure good venti-
lation. Harmful and/or toxic gases and vapors
may be emitted.
6.3 Selecting the right nozzle
The glass protection nozzle (7) is designed to
protect e.g. glass panes from overheating by
diverting the hot air. For removing paint.
The wide jet nozzle (8) ensures uniform air
distribution on small surfaces.
The reducer nozzle (9) provides a targeted jet
of heat for corners and for soldering work.
The reflector nozzle (10) is designed for sol-
dering and shaping tubes, for defrosting water
pipes and for shrinking insulating hoses.
Fit the corresponding nozzle attachment onto
the nozzle (1) on the device.
Warning!
Allow the device to cool down before you change
the nozzle.
6.4 Removing the guard hood (Fig. 5)
The removable guard hood (4) can be removed to
facilitate work in con ned spaces.
Hazard!
Note that there is then an increased risk of re
and burns.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
Anl_TE_HA_2000_E_SPK1.indb 16Anl_TE_HA_2000_E_SPK1.indb 16 14.01.15 15:0714.01.15 15:07
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell TE-HA 2000 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TE-HA 2000 E in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell TE-HA 2000 E

Einhell TE-HA 2000 E User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info