606197
21
Zoom out
Zoom in
Previous page
1/108
Next page
GB
- 21 -
Take care that the safety device is secure.
Never use the angle grinder without the
guard.
5.3 Test run for new grinding Wheels
Allow the right-angle grinder to run in idle for at
least 1 minute with the grinding or cutting wheel
tted in place. Vibrating wheels are to be replaced
immediately.
6. Operation
6.1. Switch (Fig. 4)
The angle grinder comes with a safety switch
which is designed to prevent accidents. To start,
push the locking lever (a) forwards, then press the
On/O switch (2).
6.1.1 Speed controller (Fig. 5)
You can select the speed by turning the speed
controller (6).
Switch position 1: approx. 3,000 rpm
Switch position 2: approx. 6,000 rpm
Switch position 3: approx. 8,000 rpm
Switch position 4: approx. 9,800 rpm
Switch position 5: approx. 10,500 rpm
Switch position 6: approx. 11,000 rpm
The best speed depends on the area of appli-
cation and the maximum rated speed of the
grinding/sanding tool. Select a speed in the range
from 3,000 to 11,000 rpm using the speed control
switch (6). You can choose from 6 di erent switch
positions. The speeds in the various switch posi-
tions are as follows:
Plus direction: Higher speed
Minus direction: Lower speed
6.1.2 Status indicator (Fig. 1)
The status indicator (7) lights up when the power
plug is connected.
Wait until the machine has reached its top
speed. You can then position the angle grin-
der on the workpiece and machine it.
6.2 Changing the grinding wheels (Fig. 7 / 8)
Use the face spanner (5) supplied to change the
grinding wheels. The face spanner (5) is stored in
the additional handle (3). Pull the face spanner (5)
out of the additional handle (3) when you need it.
Important! For safety reasons, the angle grinder
must not be operated with the face spanner (5)
inserted in it.
Pull out the power plug.
Simple wheel change by spindle lock:
Press the spindle lock and allow the grinding
wheel to latch in place.
Open the flange nut with the face spanner.
(Fig. 7)
Change the grinding or cutting wheel and
tighten the flange nut with the face spanner.
Important!
Only ever press the spindle lock when the
motor and grinding spindle are at a stand-
still! You must keep the spindle lock pressed
while you change the wheel!
For grinding or cutting wheels up to approx. 3 mm
thick, screw on the ange nut with the at side
facing the grinding or cutting wheel.
6.3 Flange arrangements when using grin-
ding wheels and cutting wheels (Fig.
8-11)
Flange arrangement when using a de-
pressed-centre or straight grinding wheel
(Fig. 9)
a) Clamping flange
b) Flange nut
Flange arrangement when using a de-
pressed-centre cutting wheel (Fig. 10)
a) Clamping flange
b) Flange nut
Flange arrangement when using a straight
cutting wheel (Fig. 11)
a) Clamping flange
b) Flange nut
6.4 Motor
It is vital for the motor to be well ventilated during
operation. Be sure, therefore, to keep the ventilati-
on holes clean at all times.
6.5 Grinding Wheels
Never use a grinding or cutting wheel bigger
than the specified diameter.
Before using a grinding or cutting wheel,
check its rated speed.
The maximum speed of the grinding or cut-
ting wheel used must be higher than the idle
speed of the angle grinder.
Use only grinding and cutting wheels that are
Anl_TE_AG_125_CE_SPK1.indb 21Anl_TE_AG_125_CE_SPK1.indb 21 22.12.14 14:2322.12.14 14:23
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell TE-AG 125 CE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TE-AG 125 CE in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell TE-AG 125 CE

Einhell TE-AG 125 CE User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info