697746
17
Zoom out
Zoom in
Previous page
1/142
Next page
GB
- 17 -
Warning!
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the va-
cuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
5.3 Fitting the dust extraction device for the
grinding/sanding plate (Fig. 3/4)
The dust extraction system prevents the accumu-
lation of dirt and high dust loads in the air, and it
makes it easier to dispose of the dust.
Place the equipment in a stable position as
shown in 5.1.
Fit the dust extraction device (6) with the tool
mounting (2) positioned as shown in Figure 3.
Secure the dust extraction device (6) by tigh-
tening the screw (7) with the Hexagon key
(11).
Make sure that the washer (4) is used for the
screw (5) (see Figure 2). The camber on the
washer must face upwards.
Place the triangular grinding/sanding plate
on the dust extraction device (6) and the
tool mounting (2) so that the pins of the tool
mounting (2) fit into the recesses of the trian-
gular grinding/sanding plate (8), then fasten
as shown in Fig. 4.
Connect your tool to an extraction unit or va-
cuum cleaner. This will provide excellent ext-
raction of chips and dust from the workpiece.
The bene ts are that you will protect both the
equipment and your own health. Your work area
will also be clean and safe.
6. Operation
6.1 Switching on/o
Slide the switch (1) forwards to switch on the
equipment.
Slide the switch (1) to the rear to switch o the
equipment.
6.2 Practical tips
Switch on the equipment.
Work away from the body.
Never move your hands into the direct vicinity
of the work area.
Use only plug-in tools which are in good wor-
king order and undamaged.
Plug-in tools
Sawing: Sawing wood and plastic.
Notes on working practice: When sawing, watch
out for foreign bodies in the workpiece and remo-
ve these if necessary. Plunge cutting is allowed
only in soft materials such as wood or plaster-
board.
Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depen-
ding on choice of sanding/grinding paper for the
sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice: This equipment o ers
particularly high performance for the sanding/
grinding of hard-to-reach corners and edges. To
sand/grind pro les and channels you can also
work with just the tip or the edge of the sanding/
grinding disk. Various sanding/grinding papers
are available, specially designed for the di erent
types of material you may be working on and the
amount you wish to remove from the surface.
The amount removed will depend largely on the
choice of sanding/grinding paper and pressure
applied to the sanding/grinding disk.
Scraping: Scraping o old paint or adhesives.
Notes on working practice: Move the plug-in tool
against the area you want to remove. Begin with
a at angle of incidence and little pressure. The
surface (e.g. wood, plaster) may be damaged if
too much pressure is used.
6.3 Speed control (Fig. 7)
You can select the speed by turning the speed
controller (4).
Plus direction: Higher speed
Minus direction: Lower speed
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
Anl_TC_MG_220_1_E_SPK9.indb 17Anl_TC_MG_220_1_E_SPK9.indb 17 21.08.2018 15:36:2321.08.2018 15:36:23
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell TC-MG 220-1E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TC-MG 220-1E in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 1,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell TC-MG 220-1E

Einhell TC-MG 220-1E User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info