14
GB
Watch out for other persons
Watch out for other persons (especially children)
when using the device, and keep them away from
your work area. Do not let anyone touch the device
or the power cable.
Store the tools in a safe location
Store unused devices in a dry, locked location that is
out of the reach of children.
Avoid overloading the device
Operate the device only within the specified output
range. Do not use any low-powered machines for
heavy duty work. Do not use tools to perform work
for which they were not intended.
Maintain a steady foothold
Ensure that you maintain a steady foothold while
working. Avoid abnormal body positions and always
keep your balance.
Pull out the mains plug
Pull out the mains plug when not using the tool, prior
to maintenance, and when changing the drill bit.
Avoid unintentional start-up
Ensure that switch is turned off when plugging the
plug into the socket.
Keep an eye on your work
Always keep an eye on your machine and the object
you are working on. Never use the machine when
you are not concentrating or are distracted. Never
use the machine when you are under the influence of
alcohol or are taking medication.
Check the tool for damage
Before using the tool, safety devices and any slightly
damaged parts must be carefully checked to ensure
that they are in good working order. Visually examine
the tool’s power cable on a regular basis. All parts
must be correctly assembled and meet all the
conditions required to ensure proper operation.
Unless otherwise specified in the operating
instructions, any damaged safety devices and parts
must be properly repaired or replaced by a
professionally recognized workshop. Never use tools
with defective On/Off switches.
Warning! Using any plug-in tools and accessories
other than those specified in these operating
instructions can lead to injury.
Maximum workpiece size
Workpieces (max. 20 x 20 cm) may only be
processed if they can be clamped securely on the
drill table or in the vise.
Now, please read and follow all steps and
procedures included in the operating
instructions.
5.0. Installation
5.1. Assembling the machine (Figs. 1/4/5)
b Place the base plate (1) in the desired position.
b Fasten the pillar (2) with flange using the
supplied screws (3).
b Insert the screw gear in the drill table support.
b Then insert the gear rack (30) in the drill table
support (5) with the teeth facing the screw gear
(identical projection).
b Now slip these parts together over the pillar (2).
In doing so, make sure that the gear rack is
correctly seated in the teeth of the screw gear.
b To secure the gear rack at the top end, slip on
the guide sleeve (29) over the pillar and fasten
with the screw.
b You can now fit the table and clamp in place with
the clamping lever. Following this, fit the crank
(27) and fasten tightly with the screw (28).
b Finally, fit the complete bit head to the pillar.
Align the head so that it is horizontal to the base
plate and fasten it in position with the screws
(35).
b Screw the 3 supplied handles (9) in the handle
mounts.
b Before you mount the drill chuck with the MK
shank, check that both parts are clean. Insert the
taper mandrel in the taper of the drill chuck with
a powerful jolt. Then insert the taper in the
spindle (Fig. 13)
b Check the tension of the V-belt regularly before
use (Fig. 9).
Important: All bare parts are greased in order to
protect them from corrosion. Before mounting the
drill chuck (10) onto the spindle (11), both parts must
be completely degreased using an environmentally
friendly solvent. This ensures optimal transmission of
power.
5.2. Installing the machine (Figs. 4/5)
Before you use the drill for the first time it must be
permanently fixed in position. Use both mounting
holes (12) in the base plate to do this. Ensure that
the machine is freely accessible for operation,
adjustment and maintenance.
Important: The fixing screws may only be tightened
