782358

Einhell RT-SD 3.6-2 Li Manual

19
Zoom out
Zoom in
Previous page
1/100
Next page
GB
- 19 -
the charging cable is connected to the charging
adapter.
The red LED on the battery capacity indicator (5)
indicates that the battery is being charged. When
the charging has fi nished, the red LED will go out
and the green LED will begin to shine.
Important. The handle may become a little warm
during the charging process. This is normal.
If the battery fails to charge, please check
• whether there is voltage at the socket outlet
• whether there is good contact at the charging
contacts of the charging unit
If the battery still fails to charge, send
• the charging unit
• and the screwdriver
to our customer service center.
Timely recharging of the battery will help it serve
you well for a long time. You must recharge the
battery when you notice that the power of the
cordless screwdriver drops.
6.2 Changeover switch (Fig. 3/Item 10)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. Change the direction of rota-
tion only when the equipment is at a standstill.
If you fail to observe this point, the gearing may
become damaged. When the slide switch is in the
middle position, the On/Off switch is blocked.
6.3 On/Off switch (Fig. 3 / Item 9)
Press the On/Off switch to switch the cordless
screwdriver on. Release the On/Off switch again
to switch it off .
6.4 LED lamp (Fig. 3/Item 2)
The LED lamp (2) can be used to additionally illu-
minate the area where you want to drill or screw.
The LED lamp (2) will be lit automatically as soon
as you press the On/Off switch (9).
6.5 Angle setting (Fig. 3+4/Item 7)
The screwdriver can be locked into 2 diff erent
angle settings. To do so, press and hold the lo-
cking button (7) and move the screwdriver into the
desired position. Then release the locking button
(7) again.
Important. Before you switch on the screwdriver,
make sure that it is correctly locked in the angle
position in question.
6.6 Battery capacity indicator (Fig. 5/Item 5)
Remove the cordless screwdriver from the char-
ging unit/charging station.
Press the button for the battery capacity indicator
(6). The battery capacity indicator (5) indicates
the charge state of the battery on 3 colored LEDs.
All the LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
6.7 Torque setting (Fig. 5 / Item 3)
The torque for a particular screw size is set with
the setting ring (3). The torque is dependent on a
number of factors:
• On the type and hardness of the material
involved
• On the type and length of the screws used
• On the requirements that the screw connec-
tion has to satisfy
The grating disengagement of the coupling in-
dicates that the selected torque level has been
reached.
Important. Only ever adjust the setting ring
when the equipment is at a standstill.
6.8 Magnetic screw holder (Fig. 5/Item 4)
Screws can be placed on the magnetic screw hol-
der for easy reach during operation.
6.9 Changing the bit (Fig. 6)
Important. Set the changeover switch to its center
position whenever you carry out any work (for
example changing the bit, maintenance , etc.) on
the cordless screwdriver.
• Pull back and hold the locking sleeve (13).
• Insert the bit (a) in the bit chuck (1) and let go
of the locking sleeve (13).
• Check that the bit is locked in placed by
pulling on it.
Anl_RT_SD_3_6_1_Li_SPK1.indb 19Anl_RT_SD_3_6_1_Li_SPK1.indb 19 20.11.13 08:3420.11.13 08:34
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell RT-SD 3.6-2 Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell RT-SD 3.6-2 Li in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 1.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell RT-SD 3.6-2 Li

Einhell RT-SD 3.6-2 Li User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info