Manual Einhell RT-RH 32 (page 16 of 88) (English, Danish, Swedish, Norwegian)

78417

Zoom out

Zoom in

1/88

- 16 -

stop (7).

•

Set the depth stop (7) to the same level as

the drill bit.

•

Pull the depth stop (7) back by the required

drilling depth.

•

Retighten the locking screw (a).

•

Now drill the hole until the depth stop (7) tou-

ches the workpiece.

5.3. Tool insertion (Fig. 4)

•

Clean the tool before insertion and apply a

thin coating of drill bit grease to the shaft of

the tool.

•

Pull back and hold the locking sleeve (2).

•

Insert the dust-free tool into the tool mounting

as far as it will go whilst turning it. The tool will

lock itself.

•

Check that it is properly secure by pulling the

tool.

5.4 Tool removal (Fig. 5)

Pull back and hold the locking sleeve (2) and re-

move the tool.

5.5 Dust collection device (Fig. 6)

Slide the dust collection device (a) over the drill

bit before carrying out any hammer drilling verti-

cally above your head.

6. Operation

Danger

To prevent all danger, the machine must only be

held using the two handles (6/8). Otherwise there

may be a risk of suﬀ ering an electric shock if you

drill into cables.

6.1 Switching on and oﬀ (Fig. 1)

To switch on:

Press the control switch (4).

To switch oﬀ :

Release the control switch (4).

6.2 Hammer stop facility (Fig. 7)

The hammer drill has a hammer stop facility for

gentle initial drilling.

•

Turn the rotary switch for the hammer stop

facility (5) to position (B) to switch off the

hammer facility.

•

To switch on the hammer facility again the

rotary switch for the hammer stop facility (5)

must be turned back to position (A).

6.3 Rotation stop facility (Fig. 8 / 9)

The rotation function of the hammer drill can be

switched oﬀ for chiseling jobs.

•

To do this, press the button (C) on the rotary

switch (3) whilst at the same time turning the

rotary switch (3) into position A (see Fig. 8).

•

To switch on the rotation facility again, press

button (C) on the rotary switch (3) whilst at

the same time turning the rotary switch (3)

into position B (see Fig. 9).

Notice

Please note that it is not possible to operate the

hammer drill with the hammer stop and rotation

stop facilities both active at the same time.

Notice

Only low pressure is required for hammer drilling.

Excessive pressure will exert an unnecessary

force on the motor. Check the drill bits at regular

intervals. Sharpen or replace blunt drill bits.

7. Replacing the power cable

Danger!

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel

to avoid danger.

8. Cleaning, maintenance and

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

8.1 Cleaning

•

Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

•

We recommend that you clean the device

immediately each time you have finished

using it.

•

Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The

ingress of water into an electric tool increases

Anl_RT_RH_32_SPK1.indb 16Anl_RT_RH_32_SPK1.indb 16 01.07.14 10:5801.07.14 10:58

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell RT-RH 32 in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell RT-RH 32

Einhell RT-RH 32 User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell RT-RH 32 Manual

Product: