461658
7
Zoom out
Zoom in
Previous page
1/60
Next page
7
GB
1. Description
The party radiator is used outdoors to heat nearby areas.
A burner inside the perforated plate body produces the necessary heat, which is radiated to the immediate
surroundings by an aluminium reflector as well as by the perforated plate itself.
The party radiator has to be set up on a level, incombustible surface with no - or only a very slight - gradient.
To make it easier to change the gas bottle, the body can be raised and locked in place on the appliance itself.
The party radiator is designed to work only with propane-butane (liquefied gas). It is connected directly to the
gas bottle by means of a DVGW-tested and approved hose pipe and a liquefied gas regulator (for outlet see
nameplate, capacity 1.5 kg/h). The following regulations have to be observed and adhered to when making the
connection:
Ȝ Technical regulations concerning liquefied gas (e.g. TRF)
Ȝ Guidelines published by liability insurance associations concerning the use of liquefied gas in special
applications
The burner and all sheet-metal parts and tube parts visible from the outside are made of rust-proof steel.
To start the radiator, open the gas bottle, „turn“ the knob to high setting, „press“ the knob (for approx. 10 sec.)
and „actuate“ the piezo igniter.
The regulator knob has the settings „zero“, „high“ and „low“. Infinitely variable intermediate settings are
possible. A thermoelectric ignition cut-out prevents gas escaping if there is no flame.
The foot, body, connecting pieces and top are made of powder-coated steel for outdoor duty.
The perforated plate body, burner and screws are made of ground high-grade steel.
The reflector shade is made of aluminium.
2. Technical data
Dimensions Total height 2165 mm
Reflector diameter 850 mm
Power rating 12,0 kW
Consumption approx. 0,94 kg/h in high setting
Fuel Propane/butane liquefied gas
Ignition Piezo igniter
Monitoring Thermoelectric flame monitor
Regulator Infinitely adjustable
Gas supply Gas bottles up to 11 kg
3. Assembly
Ȝ Before you start to assemble the party radiator, remove the protective plastic coverings.
Ȝ Carry out the assembly work on a clean surface where the parts will not be scratched.
Ȝ The assembly steps are illustrated on page 6.
Ȝ First screw three stems (Item 2) loosely to the base (Item 1) and fit the wheels (Item 11).
Ȝ Insert the connecting piece (Item 5) from the side and fasten from underneath. Important: Observe the
layout assignment!
Ȝ Put on the framework case (Item 3) and fasten loosely with the raised cheesehead screws (layout
asignment!).
Ȝ Slide the framework lid (Item 4) over the connecting piece and the framework case. Arrange the position of
the holes in the framework lid, the framework case and the blind rivet nuts size M5 of the stems so that
they coincide and tighten.
Ȝ Now tighten all the screws.
Ȝ Mount the burner group (Item 6), inserting the hose pipe in the connecting piece (Item 5) as you do so. Be
careful not to kink the hose pipe or damage the setting mechanism.
Ȝ Now fasten the burner group with the hex screw size M6 x 16 and the washer ( 12.5. Finally, put on the
reflector (Item 7) and screw it in place.
Ȝ Insert the gas bottle. Connect the hose pipe to the pressure regulator and the pressure regulator to the
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell PS 1002 NIRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell PS 1002 NIRO in the language / languages: English, German, Dutch, Danish, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info