Manual Einhell MK 2600E (page 22 of 88) (English, German, French, Italian, Spanish)

724141

Zoom out

Zoom in

1/88

- 22 -

5. Operation

5.1 Description of the control elements (Fig.

1. “MODE” switch – function

2. Unassigned

3. “TIMER” LED – timer on

4. “TIMER” switch

5. “UP” selector switch – higher

6. “ON/OFF” switch – On/Off

7. “DOWN” selector switch – lower

8. „Sleep“ switch - sleep function

9. „Sleep function set“ LED

10. “SPEED” switch – fan speed

11. „Fan fast“ LED

12. Remote control sensor

13. „Fan slow“ LED

14. “COMP” LED – compressor running

15. LED – indicator panel

16. “F.W.” LED – condensate tray full

17. „Fan function set“ LED

18. „Automatic mode set“ LED

19. „Cool mode set“ LED

5.2 Switching the device on and off

Press the On/Off switch. The device starts up

automatically. If the ambient temperature:

•

is higher than 23°C the device will run in coo-

ling mode;

•

if it is between 20°C and 23°C the device will

run in fan mode.

The status of the device, or mode in which it is

running, will be shown by the corresponding

LEDs (see indicator panel).

Note: The LED indicator panel shows the current

room temperature (0-50°C).

To switch the device off, press the On/Off switch

again.

Important.

After you have switched off the unit, you must

wait at least three minutes before you switch

it on again. This protects the compressor from

overloads and considerably extends its service

life.

The cooling system switches itself off whenever

the room temperature is below the value set on

the thermostat. The air circulation/ventilation fan

continues to run as set. If the room temperature

increases again, the cooling system switches on

again.

5.3 Selecting the mode

Press the “Mode” selector (MODE) in the

sequence “Automatic”, “Cool”, “Fan”. The LED for

the selected mode lights up (see indicator panel).

5.4 Setting the set-point temperature

Press the “Warmer” selector (UP) or “Cooler”

(DOWN) to set your desired set-point

temperature. If you press the “Warmer” or

“Cooler” selector, the LED indicator panel

will show your desired set-point temperature.

Otherwise the LED indicator panel always shows

the current room temperature.

5.5 Selecting the fan speed

Press the “Fan speed” selector to set the desired

fan speed.

The LED for the mode lights up (see indicator

panel).

If the device is in “Automatic mode” (AUTO) the

fan speed will be selected automatically by the

device in dependency on the room temperature.

The corresponding LED lights up. The “Fan

speed” is deactivated.

5.6 Setting the timer

Press the switch for the “Timer” (TIMER) to

set the desired operating time (1 - 12 h). The

“Timer” (TIMER) LED lights up. If the timer is

set, the device starts automatically. If you press

the “Timer” switch, the time you have set will be

shown in the LED indicator panel. If the timer

has not been switched on, the device will run

continuously.

If the unit is connected to the voltage supply and

you press the TIMER switch, you can set the time

at which you wish the unit to be switched on. If,

for example, the timer shows “2”, this means that

the device will start up automatically in 2 hours

time.

5.7 Activating the sleep function (only

possible in cooling mode)

Press the “Sleep” key to activate the sleep

function. In order to prevent undercooling, the

set room temperature increases 1 °C during the

first hour and 2 °C within 2 hours. When the sleep

function is switched off the room temperature

decreases back to the set value. After the sleep

function has been on for 12 hours the equipment

switches off automatically.

Anleitung_MK_2100_E_SPK7.indb 22Anleitung_MK_2100_E_SPK7.indb 22 25.09.2018 10:12:4125.09.2018 10:12:41

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell MK 2600E in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell MK 2600E Manual

Product: