605754
30
Zoom out
Zoom in
Previous page
1/136
Next page
7.2.2 Blade
For safety reasons you should only ever have your
blade sharpened, balanced and mounted by an
authorized service workshop. For optimum results it
is recommended that the blade should be inspected
once a year.
Changing the blade (Fig. 25)
Only ever use original spare parts when having the
blade replaced. The marking on the blade must be
matched with the number given in the list of spare
parts. Never have any other model of blade fitted.
Damaged blades
Should the blade, in spite of all precautions, come
into contact with an obstruction, shut down the
engine immediately and pull the spark plug boot. Tip
the lawn mower onto its side and check the blade for
damage. Damaged or bent blades must be replaced.
Never attempt to bend a bent blade back to straight
again. Never mow the lawn with a bent or heavily
worn blade as this will cause vibrations and can lead
to further damage to the lawn mower.
Important: There is a risk of injury if you work with a
damaged blade.
Resharpening the blade
The blades can be resharpened with a metal file. In
order to avoid imbalance, the blade should be
resharpened by an authorized service workshop.
7.2.3 Checking the oil level
Important: Never run the engine with no or too little
oil. This could cause severe damage to the engine.
Use only 15W40 engine oil.
Checking the oil level:
Stand the lawn mower on a flat level surface.
Unscrew the oil dip stick (15/Pos. A) by turning
anticlockwise, pull out and wipe. Insert the dip stick
back in the filling mount as far as the stop, but do not
screw back in. Pull out the dip stick again and read
off the oil level while holding horizontally. The oil
level must be between the maximum
(Fig. 16/Item H)
and the minimum (Fig. 16/Item L). The moveable
orange plastic part on the oil dip stick provides
protection against oil foam.
Changing the oil
Change the engine oil every year before the start of
the season (in addition to the information in the
petrol service manual) when the engine is warm.
Use only engine oil (15W40).
Place a flat oil drip tray beneath the mower.
Open the oil filler screw (Fig. 15/Item A).
Open the oil drainage screw (Fig. 17). Drain the
warm engine oil into a drip tray.
Close the drain screw again when all the used oil
has been drained.
Fill up with engine oil as far as the top mark on
the dipstick.
Important! Do not screw in the oil dipstick to
check the oil level – only insert it as far as the
thread.
Dispose of the used oil in accordance with
applicable regulations.
7.2.4 Care and adjustment of the cables
Oil the cables at regular intervals and check that they
move easily.
7.2.4.1 Adjusting the cord for the engine brake
If you notice a drop in the performance of the engine
brake, the cord (Fig. 18/Item A) will need readjusting.
7.2.4.2 Drive unit cable adjustment (Fig. 19)
In the drive position of the clutch lever (Fig. 13), the
clutch lever (Fig. 1/Item 1) should be pulled up to the
top push bar. If the cable is too taut, it must be set to
a longer length. To do this, undo the lock nut (Fig.
19/Item A) opposite the main cable (Fig. 19/Item B),
extend the screw connection and then tighten the
lock nut again. If the power of the drive unit starts to
fall, the clutch tension must be increased using the
cable. To do this, the screw connection must be
reduced (using the method described above). Set the
clutch lever (Fig. 1/Item 1) so that it can just touch
the top push bar.
7.2.5 Maintenance of the air filter (Fig. 20/21)
A soiled air filter will reduce the performance of the
engine because it will prevent enough air getting to
the carburetor. It is therefore imperative that regular
checks are made. The air filter should be checked
every 25 hours and cleaned if required. If the air is
very dusty the air filter should be checked more
regularly.
Important: Never clean the air filter with petrol or
inflammable cleaning agents. Clean the air filter with
compressed air or simply by knocking out any
soiling.
7.2.6 Maintenance of the spark plug
Check the spark plug for dirt and grime after 10
hours of operation and if necessary clean it with a
copper wire brush. Thereafter service the spark
plug after every 50 hours of operation.
Pull off the spark plug boot (Fig. 22) with a twist.
Remove the spark plug with the supplied spark
plug wrench.
Assemble in reverse order.
GB
30
Anleitung_GH_PM_46_1_S_SPK1__ 31.05.13 07:33 Seite 30
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell GH-PM 46-1 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GH-PM 46-1 S in the language / languages: English, Swedish as an attachment in your email.

The manual is 5,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell GH-PM 46-1 S

Einhell GH-PM 46-1 S User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info