Manual Einhell GE-PW 45 (page 18 of 76) (English, German, French, Italian, Portuguese, Spanish)

605880

Zoom out

Zoom in

1/76

- 18 -

6. Operation

The pump must be ﬁ lled with the transport ﬂ uid at

the ﬁ ller neck (Figure 3 / Item 2) before the engine

is started.

Note: We advise that you install a non-return valve

in the intake line and ﬁ ll it with water before you

start the machine for the ﬁ rst time.

6.1 Starting the engine

1. Set the On/Oﬀ switch (Figure 1 / Item 6) to

“ON”.

2. Set the petrol cock (Figure 4 / Item 8) to the

“ON” position.

3. If the engine is cold, set the choke lever (Fi-

gure 4 / Item 9) to “Choke”.

4. Move the throttle lever (Figure 4 / Item 10) to

the center position.

5. Pull the starter cord (Figure 4 / Item 7) until

the engine starts.

6. When the engine has been running for ap-

prox. 30 seconds, move the choke lever to

“Run”.

If the engine is warm, leave the choke lever in the

“Run” position when starting.

Explanation of the positions of the throttle

lever (Figure 4 / Item 10):

“Tortoise”:

Engine in idling

“Hare”:

Maximum delivery rate

6.2 Intake process

•

During the priming process, the shut-off

devices present in the pressure pipe (spray

nozzles, valves etc.) must be completely

open so that the air in the suction pipe can

escape freely.

•

Depending on the suction height and the air

quantity in the suction pipe, the initial priming

process can last for approx. 0.5 min. – 5 min.

In the case of longer priming periods, top up

again with water.

•

If the pump is removed after use, it is essen-

tial that it is filled with water again the next

time it is connected and started.

6.3 Stopping the engine

•

Set the On/Off switch to “OFF”.

•

Close the petrol cock.

Running-in period:

For the ﬁ rst 20 hours of operation, the motor must

not be operated at full throttle for too long.

Misﬁ res, start-up diﬃ culties:

Check whether

•

fuel is flowing into the carburetor;

•

the fuel filter is clean;

•

the carburetor air valve is open;

•

the air filter is clean;

•

the spark plug is clean and the electrode gap

is between 0.6 and 0.7mm.

7. Cleaning, maintenance, storage

and ordering of spare parts

Disconnect the spark plug boot before doing any

cleaning and maintenance work!

7.1 Cleaning

•

Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

•

We recommend that you clean the device im-

mediately each time you have finished using

it.

•

Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could

attack the plastic parts of the equipment. En-

sure that no water can seep into the device.

7.2 Maintenance

In this connection, please also read the attached

service information

7.2.1 Changing the oil

The engine oil is best changed when the engine

is at working temperature

•

Use only engine oil (10W40).

•

Place the machine on a slightly inclined sur-

face so that the oil drain plug is at the lower

end (Figure 5a / Item A).

•

Remove the oil filler screw (Figure 5a / Item

B).

•

Remove the oil drain plug and drain the warm

engine oil into a suitable container.

Anl_GE_PW_45_SPK7.indb 18Anl_GE_PW_45_SPK7.indb 18 27.06.13 08:5727.06.13 08:57

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GE-PW 45 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell GE-PW 45 Manual

Product: