Manual Einhell GE-HC 18 Li T Kit (page 26 of 140) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

605964

Zoom out

Zoom in

1/140

- 26 -

5.11 Fitting the battery (Fig. 22 – 23)

Press the side pushlock button (T) of the battery

pack as shown in Fig. 22 and push the battery

pack into the mount provided. When the battery

pack is positioned as in Fig. 23, make sure that

the pushlock button latches in place! To remove

the battery pack, proceed in reverse order.

5.12 Charging the battery (Fig. 24)

1. Take the battery pack out of the equipment.

Do this by pressing the pushlock button (T).

2. Check that your mains voltage is the same as

that marked on the rating plate of the battery

charger. Insert the power plug of the charger

(21) into the mains socket outlet. The green

LED will then begin to ﬂ ash.

3. Insert the battery pack (1) into the battery

charger (21).

4. In the section entitled „Charger indicator“ you

will ﬁ nd a table with an explanation of the LED

indicator on the charger.

The battery pack can become a little warm during

the charging. This is normal.

If the battery pack fails to charge, check:

•

whether there is voltage at the socket outlet

•

whether there is good contact at the charging

contacts.

If the battery pack still fails to charge, send

•

the charging unit

•

and the battery pack

to our customer service center.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly.

You must recharge the battery pack when you

notice that the power of the cordless equipment

drops. Never fully discharge the battery pack. This

will cause it to develop a defect.

6. Operation

Please note that the statutory regulations gover-

ning noise abatement may diﬀ er from one loca-

tion to another.

Caution! Always use the shoulder strap when

working with the equipment. Always switch oﬀ the

equipment before you take oﬀ the shoulder strap.

Otherwise there is a risk of injury.

Put on the shoulder strap as described above, ﬁ t

the required mounting kit and adjust the equip-

ment to suit your needs.

Switching on/oﬀ

Switching on

•

Hold the equipment by the handles with both

hands (thumbs under the additional handle).

•

Slide the safety lock-off (Fig. 3/Item 4) to the

front and hold.

•

Switch on the equipment with the On/Off

switch (Fig. 3/Item 3). You can then release

the safety lock-off.

Switching oﬀ

Release the On/Oﬀ switch (Fig. 3/Item 3).

7. Working with the chainsaw

mounting kit

Preparations

To ensure that you can work safely, check the fol-

lowing points before every use:

Condition of the chainsaw

Inspect the chainsaw before the start of work for

damage to the housing, the power cable, the saw

chain and the cutter rail. Never use a chainsaw

which is obviously damaged.

Oil container

Fill level of the oil container. Even while working,

keep checking that suﬃ cient oil is in the system.

To avoid damaging the chainsaw, never run the

saw if there is no oil in the system or if the oil

drops below the “min” mark. On average, a single

ﬁ lling will last around 20 minutes depending on

the number of pauses in cutting and the loads

involved.

Saw chain

Tension of the saw chain, condition of the cutting

ele-ments. The sharper the chainsaw, the easier

and more controllable it is to operate the chain-

saw. The same also applies to the chain tension.

Also while working you should check the chain

tension no less than every 10 minutes in order to

increase your safety. New saw chains in particular

often tend to expand more.

Safety clothing

Always wear appropriate tight-ﬁ tting safety

clothing like special trousers which protect

against cuts, protective gloves and safety shoes.

Anl_GE_LC_18_Li_T_SPK7.indb 26Anl_GE_LC_18_Li_T_SPK7.indb 26 11.08.14 13:0811.08.14 13:08

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GE-HC 18 Li T Kit in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell GE-HC 18 Li T Kit Manual

Product: