605765

Einhell GC-SC 2240 P Manual

21
Zoom out
Zoom in
Previous page
1/96
Next page
GB
- 21 -
1. Open the petrol cock (Fig. 7 / Item B). Set the
cock to “ON” for this purpose.
2. Set the choke lever (Fig. 7/Item C) to the
“Choke” position.
Note: Normally the choke is not required to
restart a warm engine.
3. Move the throttle lever (Fig. 1 / Item 7) to the
center position.
4. Press the engine brake lever (Fig. 6 / Item
1) and pull the starter cable (Fig. 7 / Item A)
forcefully until the engine starts.
5. Allow the engine to warm up briefl y and then
set the choke lever (Fig. 7 / Item B) to the
“RUN” Position.
6. The speed of the cutter unit can be controlled
using the throttle lever (Fig. 6 / Item 7) (tortoi-
se = slow / rabbit = fast).
Important: Always pull the starter cable slowly
until you feel the initial resistance before you then
pull it quickly to start the engine. Do not allow the
starter cable to whip back of its own accord.
Important: The scarifi er roller begins to rotate as
soon as the engine is started.
Important! Never open the ejector fl ap when the
motor is running. A rotating cutting unit can cause
injuries.
Always fasten the ejector fl ap carefully. The fl ap
fl ips back to the “Closed” position by the tension
springs!
Always ensure that a safe distance (provided
by the long handles) is maintained between the
user and the housing. Be especially careful when
scarifying and changing direction on slopes and
inclines. Maintain a solid footing and wear sturdy,
non-slip footwear and long trousers. Always sca-
rify along the incline (not up and down).
For safety reasons, the scarifi er may not be used
to scarify inclines whose gradient exceeds 15
degrees.
Use special caution when backing up and pulling
the scarifi er (tripping hazard)!
Adjusting the working depth (Fig. 8)
To set the working depth, push the lever for set-
ting the depth (Fig. 8 / Item 4) gently away from
the device, set the required depth and then lock
the lever back into position.
Important. For transport move the lever for set-
ting the depth to the highest position.
Tips for proper working
It is recommended that you overlap scarifying
paths a little. Try to scarify in straight lines for a
nice, clean look. Insodoing, the aeration swaths
should always overlap each other by a few centi-
meters in order to avoid bare strips.
As soon as grass clippings start to trail the scari-
fi er, it is time to empty the grass basket.
Important! Before taking off the grass basket,
switch off the motor and wait until the roller has
come to a stop.
To remove the grass basket, lift up the ejector fl ap
with one hand, while unhooking the basket with
the other.
How frequently you should scarify your lawn is
determined primarily by the speed at which the
grass grows and the hardness of the soil.
Keep the underside of the equipment clean and
remove soil and grass build-up. Deposits make it
more diffi cult to start the aerator and decrease the
quality of the scarifying.
Always scarify along inclines (not up and down).
Switch off the motor before doing any checks on
the roller.
Important!
The roller rotates for a few seconds after the
motor is switched off . Never attempt to stop the
roller. In the event that the rotating roller strikes
an object, immediately switch off the equipment
and wait for the roller to come to a complete stop.
Then inspect the condition of the roller. Replace
any parts that are damaged.
7. Cleaning, maintenance, storage,
transport and ordering of spare
parts
Important:
Never work on or touch conducting parts on the
ignition unit with the engine running. Always pull
the spark plug boot from the spark plug before
starting any work of care or maintenance. Never
perform any work on the machine while it is run-
ning. Any work not described in these Operating
Instructions must be performed by an authorized
service workshop only.
Anl_GC_SC_2240_P_SPK7.indb 21Anl_GC_SC_2240_P_SPK7.indb 21 08.10.14 09:0108.10.14 09:01
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell GC-SC 2240 P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GC-SC 2240 P in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info