605751

Einhell GC-EM 1030 Manual

24
Zoom out
Zoom in
Previous page
1/208
Next page
GB
- 24 -
Fitting the wheels (Fig. 3a to 3d):
Follow Fig. 3a to 3d for fi tting the wheels.
Fitting the push bar (Fig. 4a to 4c)
Take a bottom push bar (Fig. 2 /Item 3) and fasten
it with the nut (Fig. 2/Item 13) as shown in Fig. 4a.
Proceed in the same way on the other side. Screw
the top push bar (Fig. 2/Item 1) to the bottom
push bar (Fig. 2/Item 3) as shown in Fig. 4b.
Then attach the power cable to the push bar (Fig.
4c/Item A) using the cable clips (Fig. 2/Item 14).
Mounting the grass basket (Fig. 5a to 5c)
Plug the bottom and the top part of the grass box
together (Fig. 5a/Item 9, 10). Ensure that all the
plastic lugs engage correctly. Next push the grass
box handle (Fig. 5b/Item 11) into the openings on
the grass box. Check that the handle is secure
and correctly positioned. Before you fi t the grass
basket you must ensure that the motor is swit-
ched o and the blade is not rotating.
The grass box must be attached to the two hooks
on the mower (Fig. 5c). To do this, open the ejec-
tor fl ap with one hand (Fig. 5c/Item 4) and attach
the grass box with the other hand. The ejector fl ap
is held against the grass box by a spring.
Adjusting the cutting height
Warning!
Adjust the cutting height only when the motor has
been switched o and the power cable has been
disconnected.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch o the motor and pull out the
power plug.
The cutting height is adjusted as shown in Figure
6. To do so, turn the equipment upside down or tilt
it to the side. Position both the front and rear axle
in the same notch, so that the cutting blade runs
parallel to the lawn.
Position Cutting depth
1 70mm
2 50mm
3 30mm
Power supply
The lawn mower can be connected to any light
socket-outlet with a 220-240 Volt alternating
current. However, the socket outlet must have an
earthing contact protected by a 16 A circuit brea-
ker. Additionally, a residual current device (RCD)
circuit-breaker with max. 30 mA must be used!
Power cable for the device
Please only use power cables that are not dama-
ged. The total length of the power cable should
not exceed 50 meters; going beyond this distance
will reduce the power output of the electric motor.
The power cable must have a cross-section of 3
x 1.5 mm
2
. The insulating sheath of lawn aerator
power cables is frequently damaged.
Some of the causes for this are:
•
Cuts caused by running over the cable
•
Pinching when the power cable is dragging
under doors and pulled through windows.
•
Cracking due to old age of the insulation
•
Kinking by improperly fastening or guiding the
power cable
The power cables must, at the very minimum, be
of type HO5RN-F and 3-stranded. The cable type
must be printed somewhere on the power cable.
Only purchase power cables that are marked as
such! Plugs and socket couplers for the power
cables must be made from rubber and be splash-
proof. There is a limit to how long power cables
can be. Longer power cables require larger con-
ductor cross-sections. Power cables and connec-
ting lines must be regularly checked for damage.
Ensure that the lines are de-energized before
checking them. Completely unwind the power
cable. Also check power cable entry points, plugs
and socket couplers for kinks.
6. Operation
Connect the power cable to the power plug (Fig.
1/Item 7) and secure the power cable with the
cable stress-relief clip (Fig. 7). Use the fasteners
(cable holders) for the power cable.
Caution!
To prevent the machine switching on accidentally,
the lawn mower is equipped with a safety switch
(Fig. 7/Item 1) which must be pressed before the
ON switch (Fig. 7/Item 2) can be activated. The
lawn mower switches itself o when the switch is
released.
Anl_GC_EM_1030_SPK7.indb 24Anl_GC_EM_1030_SPK7.indb 24 16.10.14 10:1416.10.14 10:14
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell GC-EM 1030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell GC-EM 1030 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info