Manual Einhell BT-MG 135-1 (page 19 of 100) (English, Danish, Swedish, Norwegian)

605676

Zoom out

Zoom in

1/100

- 19 -

The projection is not allowed to exceed 20 mm!

5.3 Installing the ﬂ exible shaft (Figs. 3/5a)

•

Unscrew the cover (5) from the front of the

equipment.

•

Undo the collet chuck nut (3).

•

Insert the internal schaft (a) of the flexible

shaft into the collet chuck (3).

•

Tighten the collet chuck nut (3).

•

Now tighten the ring (b) on the multi-tool.

5.3.1 Inserting the various tools in the ﬂ exible

shaft (Fig. 5b)

1. Press the locking pin (8) into the hole in the

ﬂ exible shaft (13) and turn the shaft until the

pin latches in place.

2. Remove the clamp nut (3), insert the mat-

ching clamping sleeve (11) and reﬁ t the

clamp nut.

3. Insert the required tool into the clamping

sleeve as far as the stop and screw the collet

chuck nut tight.

5.4 Using the stand (Fig. 6)

•

Fit the stand to a workbench

•

The stand is adjustable in height and can be

•

adjusted as shown in Fig. 6.

•

The multi-tool can now be attached to the

stand.

6. Using the tool for the ﬁ rst time

•

Make sure that the drive unit is switched off.

•

Check that the mains voltage specified on the

rating plate of the power supply unit is the

same as your mains supply. Only then should

you insert the plug of the power supply unit

into a socket-outlet.

6.1. ON/OFF switch (Fig. 3)

Turn on the equipment by setting the On/Oﬀ

switch (1) to “I”.

Turn oﬀ the equipment by setting the On/Oﬀ

switch (1) to “0”.

6.2. Speed selector (Fig. 3)

The required speed can be set with the speed

control (2).

The correct speed depends on the tool used and

the type of material being processed.

6.3 Directions for use

•

With small milling cutters / grinding pins: Use

a high speed.

•

With large milling cutters / grinding pins: Use

a low speed.

6.4 Tips

•

Exert only moderate pressure on the workpi-

ece and allow it to be processed at uniform

speed.

•

You will not finish your work sooner by exer-

ting heavy pressure. On the contrary, heavy

pressure will cause the drive unit to slow

down or stop and will overload the motor.

•

For your own safety, use a vise or screw

clamp to secure small workpieces.

•

Precision work/engraving: Hold the drive unit

like a pen (single-handed).

•

Rough work: Hold the drive unit like the hand-

le of a hammer (two-handed).

7. Accessories

7.1. Accessories (Fig. 7 / Fig. 1; Item 3/18)

1 Abrasive paper

2 Grinding belt (small)

3 Grinding belt (large)

7.2. Accessories (Fig. 8 / Fig. 1; Item 12)

1 Cutting wheel (ﬁ ne)

2 Cutting wheel (coarse)

7.3. Accessories (Fig. 9 / Fig. 1; Item 5)

1 Cutter (cylindrical, large)

2 Cutter (cylindrical, small)

3 Cutter (pointed)

4 Cutter (ball-shaped)

7.4. Accessories (Fig. 10 / Fig. 1; Item 2/10)

1 Grinding wheel

2 Felt polishing wheel

7.5. Accessories (Fig. 11 / Fig. 1; Item 9)

1-6 Grinding pins

7.6. Accessories (Fig. 12 / Fig. 1; Item

4/12/16/17)

1 Diamond cutting wheel

2 Clamping spindle for diamond cutting wheel

3 Grinding head for grinding belts (small)

4 Grinding head for grinding belts (large)

5 Pot brushes

Anl_BT_MG_135_1_SPK1.indb 19Anl_BT_MG_135_1_SPK1.indb 19 05.05.14 15:0705.05.14 15:07

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell BT-MG 135-1 in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell BT-MG 135-1

Einhell BT-MG 135-1 User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 64 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell BT-MG 135-1 Manual

Product: