606191
18
Zoom out
Zoom in
Previous page
1/96
Next page
GB
- 18 -
5. Before starting the equipment
Be sure to read the following information before
you put the cordless screwdriver into operation:
1. Charge the battery only with the charging unit
supplied.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
Additional handle (Fig. 1 /Item 13)
The additional handle (13) enables you to achieve
better stability whilst using the equipment.
The additional handle (13) is secured to the
housing by a clamp. It can be screwed to the right
or left side.
6. Operation
6.1 Charging the battery (Fig. 2-3)
1. Remove the battery pack (5) from the handle
(Fig. 2) by pressing the pushlock buttons (8)
on the left and right side of the battery pack
(5).
2. Check that your mains voltage is the same as
that marked on the rating plate. Plug the char-
ging cable (7) of the charging unit (6) into the
power socket. The green LED on the charging
unit then comes on.
3. Insert the battery pack (5) into the battery
charger (6). The red LED will come on to in-
dicate that the battery pack is being charged.
Charging has nished when the red LED
goes out and the green LED comes on again.
The battery pack may become a little warm
during the charging process. This is normal.
Caution! At temperatures of 45°C and higher the
battery cannot be charged. In this case remove
the battery from the charger, let it cool down and
then recharge it.
If the battery pack fails to charge, check for the
following:
Voltage at the power socket
Good contact at the charging contacts of the
charging unit
If the battery pack still fails to charge, send
the charging unit
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless equipment
drops. Never fully discharge the battery pack. This
will cause it to develop a defect!
6.2 Torque setting (Fig. 4 / Item 1)
The cordless hammer drill/screwdriver is tted
with a mechanical torque selector.
The torque for a particular screw size is set with
the setting ring (1). The torque is dependent on a
number of factors:
On the type and hardness of the material in-
volved
On the type and length of the screws used
On the requirements that the screw connec-
tion has to satisfy
The grating disengagement of the coupling in-
dicates that the selected torque level has been
reached.
Caution! Only ever adjust the setting ring
when the equipment is at a standstill.
6.3 Drilling/hammer drilling (Fig. 4)
For drilling purpose, adjust the torque setting
(1) to the setting “Drill”.
For hammer drilling purpose, adjust the
torque setting (1) to the setting “Hammer”.
In the drill and hammer drill settings the slip cou-
pling is non-functional. The maximum torque is
available for drilling and hammer drilling.
6.4 Changeover switch (Fig. 5/Item 3)
The slide switch above the On/O switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. To avoid causing damage to
the gearing, the direction of rotation must only be
changed when the screwdriver is at a standstill.
When the slide switch is in the middle position,
the On/O switch is blocked.
Anl_BT_CD_24_1_i_SPK1.indb 18Anl_BT_CD_24_1_i_SPK1.indb 18 04.09.12 09:4304.09.12 09:43
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell BT-CD 24-1 i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell BT-CD 24-1 i in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell BT-CD 24-1 i

Einhell BT-CD 24-1 i User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info