675833

Einhell BMST24 Manual

20
Zoom out
Zoom in
Previous page
1/88
Next page
GB
20
Specifications
BMST 24
Engine Type Air-cooled, 2-Cycle, Chrome Cylinder
Displacement 24 cm
3
Power: 0,8 kW
Dry Weight 7 kg
Fuel Capacity 500 ml
Handle Length 142 cm
Twin Line Cutting Width 43 cm
Line diameter 2,5 mm
Blade cutting width 23 cm
Handle Bike handle
Ignition Electronic
Spark plug Torch L7RTC
Drive Centrifugal clutch
General identification
1. STRINGHEAD
2. CUTTER LINE (34.051.72)
3. DEBRIS SHIELD
4. GRASS CUTTING BLADE (34.051.63)
5. BLADE GUARD
6. THROTTLE TRIGGER
7. IGNITION OFF SWITCH
8. SAFETY TRIGGER
9. CHOKE LEVER KNOB
10. STARTER ROPE HOUSING
11. FUEL TANK
12. AIR FILTER COVER
13. STARTER HANDLE
14. MUFFLER SHIELD
15. PRIMER BULB
16. DEBRIS SHIELD NUT & BOLT & WASHER
17. COUPLING
18. SHOULDER STRAP
19. EYELET FOR SHOULDER STRAP
NOTE: DO NOT use blades on these models.
SAFETY EQUIPMENT
The numbers that precede the descriptions
correspond to the numbers on the previous page to
enable you to identify the safety equipment more
easily
3 / 5 BLADE GUARD: This must be fitted at all times
to prevent the user being injured by objects
thrown up by the machine. The blade fitted in
the hood guard 3 also cuts the cutting line to the
perfect length automatically.
16 EXHAUST GUARD: This prevents hands, body
and/or inflammable material coming into contact
with the hot exhaust.
ASSEMBLY INSTRUCTIONS
FITTING THE “Bike” HANDLE (Fig. 1c - 1d)
1. To fasten the handle to the machine you will need
the following parts from the kit:
“Bike” handle (A), mounting (B), clip (C) and
screws (D).
2. Position the handle mounting (B) on the shaft in
the direction indicated by the arrow (see warning
sticker) place the clip (C) over the shaft and
tighten the two screws (D).
3. Place the “Bike” handle (A) on the mounting, fit
the other clip (C) above the guide shaft and
secure it with the other two screws (D).
4. Secure the cable going to the handle with the
cable tie (E).
Fitting the blade guard (Fig. 2a - 2b)
1. Take the gearbox collar (A) off the thread on the
gearbox casing shaft.
2. Place the guard on to the gearbox casing and line
up the fastening holes. Insert the screws (B) as
shown in the figure and tighten them.
3. Insert the gearbox collar (A) again. Ensure that
the collar spacer (C) is in the correct position,
otherwise the collar will rub on the gearbox
casing.
Anleitung_BMST 24 29.10.2004 13:35 Uhr Seite 20
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell BMST24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell BMST24 in the language / languages: English, German, Dutch, French, Italian, Swedish as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info