461621

Einhell BH2000 Manual

6
Zoom out
Zoom in
Previous page
1/24
Next page
6
the minimum distance to the housing, or the
installation height, has to be measured from the
top of the skirting.
Then drill the two fastening holes with 6 mm
diameter. The centers of the holes must be
marked so that they are 167 mm apart and
horizontal (Fig 2) and at least 1500 mm above
the floor (allow for skirtings) and the holes drilled
accordingly.
Insert wall plugs in the drilled holes, screw in the
screws and hang the heater on the wall.
4. Technical data:
Rated voltage: 230 V ~ 50 Hz
Output: 1600 W (800 W / 1600 W)
Protection type: IP24
Appliance dimensions, approx.: 27 x 13 x 37 cm
5. Proper use
The appliance is designed only for private use, not
for commercial heating purposes.
6. Starting up
Important! Before using the appliance for the first
time, check that the voltage supply is the same as
the voltage details set out on the data plate. Read
safety instructions listed under section 1.
When the heater is used for the first time or after a
long period of rest it may emit an odor for a short
time. This is not a fault.
6.1 Switch for heat output (Fig. 1 / Item 1)
Important!
The switch is to be operated only in anticlockwise
direction.
Off setting (0)
Fan setting (1)
Low heating output (2) 800 W
Maximum heating output (3) 1600 W
The switch can also be actuated with the pull cord
(Fig. 1/Item 4).
6.2 Overheat cut-out
In case of excessive heating, the heating function
shuts down automatically. If this case occurs, turn off
the appliance, disconnect the mains plug and wait a
few minutes until it has cooled. After eliminating the
cause (e.g. a covered air grille), the appliance can be
switched on again. If the overheat cut-out triggers
repeatedly, please contact your customer service
center.
7. Maintenance and cleaning
Before carrying out any cleaning and maintenance
work the appliance must be turned off,
disconnected from the power supply and cooled
down.
Maintenance and repair work may only be carried
out by an electrical servicing contractor or your
customer service center.
Check the mains lead at regular intervals for signs
of defects or damage. A damaged mains lead may
only be replaced by an electrician or the customer
service responsible for your country in compliance
with the relevant regulations.
Use a damp cloth to clean the casing.
Remove dust pollution with a vacuum cleaner.
8. Storage
The radiator has to be stored in a dry place, covered
if possible.
9. Ordering spare parts
Please provide the following information on all orders
for spare parts:
Model/type of machine
Article number of the machine
ID number of the machine
Number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
GB
Anleitung BH 2000_SPK1 16.08.2006 15:26 Uhr Seite 6
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell BH2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell BH2000 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info