the position of the mounting holes for the wall
holder (11) on the wall. Drill the mounting holes
(Ø 6 mm) for the wall holder.
2. Fig. 3: Mark the bottom holding hole for the wall
holder (7). Be sure to observe the hole distance
(100 mm) and central position in relation to the
wall holder (11). Drill the mounting hole (Ø 6 mm).
3. Fig. 3: Drill the second mounting hole for the wall
holder (7) at a distance of 293 mm vertically
above the previously made hole.
4. Fig. 4: Insert all the dowels and secure the wall
holder (7) with the screws supplied (c).
5. Fig. 4: Insert the bath heater (6) in the wall holder
(7) and screw it (d) at the bottom to the wall
holder.
6. Fig. 5: Secure the wall holder (11) for the towel
holders with the screws (c) supplied and press
the plastic cover (10) onto the wall holder (11).
7. Using the equipment
Important! Before using the equipment for the first
time, check that the voltage supply is the same as the
voltage details set out on the rating plate. Read the
safety regulations in section 1.
When the equipment is used for the first time or after
a long period of rest, it may emit an odor for a short
time. This is not a fault.
7.1 Switch for heat output (Fig. 6 / Item 2)
Off setting (A)
Fan setting (B)
Low heat output (C) 1000 W
Maximum heat output (D) 2000 W
Note: The equipment can be switched on only when
the actual room temperature is lower than the set
room temperature.
7.2 Thermostat control/room temperature control
(Fig. 6 / Item 3):
Switch on the required heat output. Turn the control to
“+” until the required room temperature is reached.
Then turn down the control until you hear a clear click.
The thermostat control switches the heater on and off
automatically to keep the room temperature at an
almost constant level.
This assumes that the heater has sufficient output for
the room you want to heat.
7.3 Towel holders
You can pre-warm or dry towels on the towel holders.
Please make sure that the air outlet at the bottom of
the housing is not obstructed.
Note: Do not overload the towel holders. They are
designed for a maximum load of 2 kg each.
7.4 Overheating guard
In case of excessive heating the equipment will shut
down automatically. If this occurs, turn off the
equipment, disconnect the mains plug and wait a few
minutes for the equipment to cool. After eliminating
the cause (e.g. a covered air grille), the equipment
can be switched on again. If the overheating guard
triggers repeatedly, please contact ISC GmbH.
8. Cleaning, maintenance and ordering
of spare parts
8.1 Cleaning
n Before carrying out any cleaning and
maintenance work the equipment must be turned
off, disconnected from the power supply and
cooled down.
n Maintenance and repair work may only be carried
out by an authorized electrical servicing
contractor or ISC GmbH.
n Check the power lead at regular intervals for
signs of defects or damage. A damaged power
lead may only be replaced by an electrician or
ISC GmbH in compliance with the relevant
regulations.
n Use a damp cloth to clean the casing.
n Remove dust with a vacuum cleaner.
8.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.3 Ordering spare parts
Please provide the following information on all orders
for spare parts:
n Model/type of the equipment
n Article number of the equipment
n ID number of the equipment
n Part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
9. Storage
Store the equipment and accessories out of children’s
reach in a dark and dry place at above freezing
temperature. The ideal storage temperature is
between 5 and 30 °C. Store the equipment in its
original packaging.
12
GB
