664228

Einhell BBH 920 Manual

9
Zoom out
Zoom in
Previous page
1/34
Next page
7
GB
1. Layout (Fig. 1)
1 Dust guard
2 Locking sleeve
3 On/Off switch
4 Additional handle
5 Drilling depth stop
6 Speed controller
7 Selector switch for drill/hammer drill/chisel
8 Locking button
9 Reverse facility
10 Clamping screw
2. Technical data
Mains voltage: 230 V ~ 50 Hz
Power: 920 Watt
Idle speed: 0-980 min
-1
Hammer rate: 0-5185 min
-1
Drilling capacity (max.): Concrete/Stone 26 mm
Weight: 3,5 kg
Vibration: 6,13 m/s
2
Sound pressure level: 93 dB(A)
Sound power level: 104 dB(A)
Protection class: / II
The noise and vibrations from this tool were measu-
red in accordance with EN 60745-2-6. This hammer
drill is not intended for use outdoors as defined in
Article 3 of the Directive 2000/14/EC.
3. Safety rules
The corresponding safety information can be
found in the enclosed booklet.
4. Preparations
Use a detector to localize pipes and/or cables in
walls with concealed electric, water or gas lines.
Before you plug in the machine, check that your
mains voltage is the same as that marked on the
rating plate.
4.1 Intended use
This hammer drill is designed for hammer drilling in
concrete, stone and masonry, for chiseling and for
drilling without hammer action in wood and metal. It
is to be used only with suitable bits.
4.2 Fitting and changing a bit (Fig. 2)
Clean the bit and coat it with a little machine
grease before you insert it.
Pull back the locking sleeve (A) and hold in this
position.
Insert the dust-free bit with a twist as far as it
goes into the chuck. The bit will automatically be l
ocked in place.
Pull on the bit to check that it is secure.
4.3 Removing a bit (Fig. 3)
Pull back the locking sleeve (A), hold and pull out the
bit.
5. Starting up (Fig. 1 - Pos. 3)
5.1 On/Off switch:
To switch on: Press switch 3
Continuous operation: Lock switch 3 with locking
button 8
To switch off: Press switch A briefly
The speed is varied by applying more or less pressu-
re on switch 3. You can preselect the speed by tur-
ning the knurled screw in switch 3.
5.2 Additional handle (Fig. 1 - Pos. 4)
For safety reasons you should always use the
hammer drill with the additional handle.
Klemmschraube (10) lockern.
Zusatzhandgriff (4) über das Bohrfutter schieben
und in die gewünschte Position drehen.
Klemmschraube (10) wieder festziehen, um den
Zusatzhandgriff (4) in dieser Position zu fixieren.
5.3 Selector switch: drill/hammer drill/chisel (Fig.
4)
For drilling, move the selector switch (7) to
position “a”
For hammer drilling, move the selector switch (7)
to position “b”
For chiseling, move the selector switch (7) to
position “c”
Important:
You only need to apply minimal pressure for hammer
drilling. Do not apply too much pressure as this will
put unnecessary strain on the motor. Check the
hammer drill at regular intervals.
Anleitung BBH 920 SPK 1 02.02.2005 7:55 Uhr Seite 7
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Einhell BBH 920 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Einhell BBH 920 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info