644136
53
Zoom out
Zoom in
Previous page
1/60
Next page
53
RISOLUZIONE DEI PROBLEMI
ATTENZIONE: fermare sempre l’unità e scollegare la candela prima di effettuare
tutte le prove correttive raccomandato nella tabella sottostante, tranne che venga
richiesto il funzionamento dell’unità.
Quando si sono verificate tutte le possibili cause e il problema non è risolto, consultare un
Centro Assistenza Autorizzato. Se si verifica un problema che non è elencato in questa tabella,
consultare un Centro Assistenza Autorizzato.
PROBLEMA POSSIBILI CAUSE SOLUZIONE
Il motore non si avvia o si
spegne solo dopo pochi secondi
dall’avvio. (Assicurarsi che
l’interruttore sia in posizione
“I”)
1. Non cè scintilla.
2. Motore ingolfato.
1. Controllare la scintilla della candela. Se
non c’è la scintilla, ripetere il test con una
candela nuova (BPMR8Y).
2. Seguire la procedura di pag.20. Se il
motore non si avvia ancora, ripetere la
procedura con una candela nuova.
Il motore parte, ma non accelera
correttamente o non funziona
correttamente ad alta velocità.
Il carburatore deve essere regolato. Contattare un Centro Assistenza Autorizzato
per regolare il carburatore.
Il motore non raggiunge la
piena velocità e / o emette fumo
eccessivo.
1. Controllare la miscela
olio / benzina.
2. Filtro aria sporco.
3. Il carburatore deve essere
regolato.
1. Utilizzare benzina fresca e un olio
adeguato per motore 2 tempi.
2. Pulire: vedi le istruzioni nel capitolo
Manutenzione filtro aria.
3. Contattare un Centro Assistenza
Autorizzato per regolare il carburatore.
Il motore si avvia, gira e accelera,
ma non tiene il minimo.
Il carburatore deve essere regolato. Regolare la vite del minimo “T (Fig.84,
pag.39) in senso orario per aumentare la
velocità; vedere capitolo Manutenzione
carburatore.
Barra e catena si scaldano e
fumano durante il funzionamento
1. Serbatoio olio catena vuoto
2. Tensionamento catena troppo
stretto
3. Malfunzionamento del sistema
di lubrificazione
1. Il serbatoio olio deve essere riempito
ogni volta che il serbatoio carburante
viene riempito.
2. Tensionamento catena; vedi istruzioni
nel capitolo Montaggio barra e catena
(Pag.12).
3. Fare funzionare a pieno regime per 15-30
secondi. Fermare e controllare che l'olio
goccioli dalla punta della barra. Se l’olio è
presente, il malfunzionamento può essere
causato dalla catena lenta o dalla barra
danneggiata. Se non c’è l'olio contattare
un Centro Assistenza Autorizzato
Il motore parte e funziona, ma la
catena non ruota
1. Freno catena inserito
2. Tensionamento catena troppo
stretto
3. Assemblaggio barra e catena
4. Catena e/o barra danneggiati
5. Frizione e/o pignone
danneggiati
1. Disinserire il freno catena; vedi capitolo
Utilizzo – Freno catena (Pag.26).
2. Tensionamento catena; vedi istruzioni
nel capitolo Montaggio barra e catena
(Pag.12)
3. Vedi le istruzioni nel capitolo Montaggio
barra e catena (Pag.12)
4. Vedi le istruzioni nel capitolo
Manutenzione barra e/o catena (Pag.34)
5. Sostituire se necessario; contattare un
Centro Assistenza Autorizzato
ATTENZIONE: non
toccare mai la catena
quando il motore è in
funzione.
TROUBLESHOOTING CHART
WARNING: Always stop unit and disconnect spark plug before performing all of
the recommended remedies below except remedies that require operation of the
unit.
When you have checked all the possible causes listed and you are still experiencing the
problem, see your Servicing Dealer. If you are experiencing a problem that is not listed in this
chart, see your Servicing Dealer for service.
PROBLEM POSSIBLE CAUSE SOLUTION
Engine will not start or will run
only a few seconds after starting.
(Make sure Ignition switch is in
start position “I”)
1. No spark
2. Flooded engine.
1. Watch for spark at spark plug tip. If there
is no spark, repeat test with a new spark
plug (BPMR8Y).
2. Follow procedure page 20 If engine still
fails to start, repeat procedure with a new
spark plug.
Engine starts but will not
accelerate properly or will not run
properly at high speed.
Carburetor requires adjustment. Contact a Servicing Dealer for carburetor
adjustment.
Engine does not reach full speed
and / or emits excessive smoke
1. Check oil fuel mixture.
2. Air filter dirty.
3. Carburetor requires adjustment.
1. Use fresh fuel and the correct 2-cycle
oil mix.
2. Clean per instruction in Maintenance-Air
Filter Section.
3. Contact a Servicing Dealer for carburetor
adjustment.
Engine starts, runs and accelerates
but will not idle.
Carburetor requires adjustment. Turn idle speed screw “T” (Fig. 84,
pag. 39) clockwise to increase idle speed.
See Operation-Carburetor Adjustment.
Bar and Chain Running Hot and
Smoking
1. Chain oil tank empty.
2. Chain tension too tight.
3. Oiler function.
1. Oil tank should be filled every time that
fuel tank is filled.
2. Tension chain per instructions in
Operation-Chain Tension section
(Pag.12).
3. Run at full throttle 15 to 30 seconds. Stop
saw and check for oil dripping from bar
tip guard and guide bar. If oil is present
the chain may be dull or bar may be
damaged. If no oil contact a Servicing
Dealer.
Engine starts and runs, but chain
is not rotating
1. Chain brake engaged.
2. Chain tension too tight.
3. Guide bar and chain assembly.
4. Chain and/or guide bar
damaged.
5. Clutch drum and/or rim
sprocket damaged.
1. Release chain brake, see Operation-
Chain Brake Section (Pag.26).
2. Tension chain per instructions in
Operation-Chain Tension section
(Pag.12).
3. Refer to Assembly-Assembling the Bar
and Chain Section (Pag.12).
4. Refer to Maintenance-Chain and/or
Maintenance-Guide Bar Section (Pag.34).
5. Replace if necessary - contact a Servicing
Dealer.
WARNING: Never touch
the chain while the
engine is running.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco MT7200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco MT7200 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info