644134

Efco MT6500 Manual

42
Zoom out
Zoom in
Previous page
1/68
Next page
88 89 90
Italiano
RIMESSAGGIO
Quando la macchina deve rimanere ferma per lungh
i
periodi:
- Vuotare e pulire i serbatoi carburante e olio in un
luogo ben ventilato.
- Smaltire il carburante e l’olio secondo le norme e
rispettando l’ambiente.
- Per vuotare il carburatore, avviare il motore e
attenderne l’arresto (lasciando la miscela ne
l
carburatore le membrane potrebbero danneggiarsi).
- Togliere, pulire e spruzzare con olio protettivo la
catena e la barra.
- Pulire accuratamente le feritoie di raffreddamento de
l
carter gruppo avviamento (Fig.88), il filtro aria
(Fig.89) e le alette del cilindro (Fig.90).
- Conservare la macchina in ambiente secco,
possibilmente non a diretto contatto con il suolo,
lontano da fonti di calore e con i serbatoi vuoti.
- Le procedure di messa in servizio dopo un
rimessaggio invernale sono le stesse che s
i
effettuano durante l’avvio normale della macchina
(pag.14 - 22).
DEMOLIZIONE E SMALTIMENTO
Buona parte dei materiali impiegati nella costruzione
della motosega sono riciclabili; tutti i metalli (acciaio,
alluminio, ottone) si possono consegnare ad un
normale ferro-recupero.
Per Informazioni rivolgersi al normale servizio d
i
raccolta di rifiuti della vostra zona.
Lo smaltimento dei rifiuti derivati dalla demolizione della
macchina dovrà essere eseguito nel rispetto
ambientale, evitando di inquinare suolo, aria e acqua.
In ogni caso dovranno essere rispettate le locali
le
g
islazioni vi
g
enti in materia.
English
STORAGE
If the machine is to be stored for long periods:
- Drain and clean the fuel and oil tank in a
well-ventilated area.
- Dispose of fuel and oil according to the rules and
respecting the environment.
- To drain the tank, start the engine and wait until the
fuel is exhausted and the engine stops (leaving fuel
mixture in the carburettor could damage the
membranes).
- Remove, clean and spray it with protective oil the
chain and the bar.
- Thoroughly clean the air intake slots on the starter
housing (Fig.88), the air filter (Fig.89) and the
cylinder fins (Fig.90).
- Store the blower in a dry place, preferably not in
direct contact with the ground, away from heat
sources and the tanks empty.
- The procedures for returning the machine to
service following winter storage are the same as
for starting up during everyday use (page 14 - 22).
DEMOLITION AND DISPOSAL
Most materials used for the chainsaw manufacturing
are recyclable; metals (steel, aluminium, and brass)
can be delivered to recycling station.
For further information contact a recycling station
service of your area.
Machine disposal must be executed in respect to the
environment, avoiding soil, air and water pollution.
Local legislation enforced in matter should be
respected in an
y
case.
Français
REMISSAGE
Lorsque l'appareil doit être entreposé pendant de
longues périodes :
- Vidanger et nettoyer les réservoirs à carburant et
huile dans un endroit bien aéré.
- Éliminer le carburant et l'huile conformément aux
normes et en respectant l'environnement.
- Pour vider le carburateur, démarrer le moteur et en
attendre l'arrêt (le fait de laisser du mélange dans le
carburateur pourrait endommager les membranes).
- Enlever, nettoyer et vaporiser de l'huile de protection
sur la cha
î
ne et la barre.
- Nettoyer à fond les fentes de refroidissement du
carter du groupe de démarrage (Fig.88), le filtre de
l'air (Fig.89) et les ailettes du cylindre (Fig.90).
- Ranger l'engin dans un endroit sec, de préférence
sans le mettre en contact direct avec le sol, loin de
toute source de chaleur et avec les réservoirs vides.
- Les procédures de mise en service après un
remisage hivernal sont les mêmes que pour le
démarrage normal de la machine (pages 14 - 22).
DÉMOLITION ET MISE AU REBUT
La plupart des matériaux utilisés dans la fabrication du
tronçonneuse sont recyclables ; tous les métaux (acier
,
aluminium, laiton) peuvent être envoyés à la ferraille.
Pour tout renseignement, contactez votre service loca
l
de collecte des déchets.
Les déchets dérivant de la démolition de l'apparei
l
doivent être éliminés en respectant l'environnement, en
évitant de polluer le sol, l'eau et l'air
Quoi qu'il en soit, il est obligatoire de respecter les
normes et législations locales en vigueur.
42
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco MT6500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco MT6500 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info