644122
56
Zoom out
Zoom in
Previous page
1/60
Next page
56
RÉSOLUTION DES PROBLÈMES
ATTENTION : toujours arrêter l'outil et débrancher la bougie avant d'intervenir
selon les indications du tableau ci-dessous, sauf indication contraire.
Si le problème persiste après avoir vérifié toutes les causes possibles indiquées, contacter un
Centre d'Assistance Agréé. En cas de problème non référencé dans ce tableau, contacter un
Centre d'Assistance Agréé.
PROBLÈME CAUSES PROBABLES SOLUTION
Le moteur ne démarre pas ou
s'arrête quelques secondes après
le démarrage. (S'assurer que
l'interrupteur se trouve sur "I")
1. Pas d'étincelle
2. Moteur noyé
1. Contrôler l'étincelle de la bougie. S'il n'y
a pas d'étincelle, répéter le test avec une
bougie neuve (L6RTC).
2. Suivre la procédure page 20. Si le moteur
ne démarre toujours pas, répéter la
procédure avec une bougie neuve.
Le moteur démarre mais n'accélère
pas correctement ou ne tourne pas
correctement à vitesse élevée.
Régler le carburateur. Contacter un Centre d'Assistance Agréé pour
régler le carburateur.
Le moteur n'atteint pas le régime
maxi et / ou dégage trop de
fumée.
1. Contrôler le mélange huile/
essence.
2. Filtre à air encrassé.
3. Régler le carburateur.
1. Utiliser de l'essence neuve et une huile
pour moteur 2 temps.
2. Nettoyer : voir les instructions au
chapitre Entretien filtre de l'air.
3. Contacter un Centre d'Assistance Agréé
pour régler le carburateur.
Le moteur démarre, tourne et
accélère, mais ne tient pas le
ralenti.
Régler le carburateur.
Régler la vis du ralenti "T" (Fig.84, page 41) en
la tournant dans le sens des aiguilles d'une
montre pour augmenter la vitesse ; voir chapitre
Entretien carburateur.
Barre et chaîne se réchauffent et
fument durant l'utilisation
1. Réservoir d'huile de la chaîne
vide
2. Chaîne trop tendue
3. Système de lubrification
défectueux
1. Remplir le réservoir d'huile à chaque
ravitaillement du réservoir à carburant.
2. Tension chaîne ; voir les instructions
au chapitre Montage barre et chaîne
(Pages 12).
3. Faire tourner 15-30 secondes au régime
maxi. Arrêter et vérifier si l'huile s'écoule
de la pointe de la barre. S'il y a de l'huile,
le dysfonctionnement peut être causé
par la chaîne détendue ou la barre
endommagée. S'il n'y a pas d'huile,
contacter un Centre d'Assistance Agréé
Le moteur démarre et tourne,
mais la chaîne ne tourne pas
1. Frein de la chaîne serré
2. Chaîne trop tendue
3. Assemblage barre et chaîne
4. Chaîne et/ou barre
endommagée
5. Embrayage et/ou pignon
endommagé
1. Desserrer le frein de la chaîne ; voir chapitre
Utilisation – Frein de la chaîne (Page 26)
2. Tension chaîne ; voir les instructions
au chapitre Montage barre et chaîne
(Pages 12)
3. voir les instructions au chapitre Montage
barre et chaîne (Pages 12)
4. Voir les instructions au chapitre Entretien
barre et/ou chaîne (Page 34)
5. Remplacer si nécessaire ; contacter un
Centre d'Assistance Agréé
ATTENTION : ne jamais
toucher la chaîne
lorsque le moteur
tourne
STÖRUNGSBEHEBUNG
ACHTUNG: Vor Durchführung aller in der untenstehenden Tabelle empfohlenen
Prüfungen das Gerät immer abstellen und die Zündkerze trennen, es sei denn, der
Betrieb des Geräts wird ausdrücklich verlangt.
Wenn alle möglichen Ursachen überprüft wurden, die Störung jedoch nicht behoben werden konnte,
wenden Sie sich bitte an eine autorisierte Kundendienststelle. Wenn ein Problem auftritt, dass nicht in
dieser Tabelle aufgeführt ist, wenden Sie sich bitte an eine autorisierte Kundendienststelle.
PROBLEM
MÖGLICHE URSACHEN
ABHILFE
Der Motor startet nicht oder geht
wenige Sekunden nach dem Start
wieder aus. (Sicherstellen, dass
der Schalter auf "I" steht)
1. Kein Zündfunke
2. Motor überflutet
1. Zündfunken der Kerze kontrollieren. Wenn
kein Zündfunken abgegeben wird, den Test
mit einer neuen Kerze wiederholen (L6RTC).
2. Vorgehen wie auf Seite 21 beschrieben.
Wenn der Motor immer noch nicht anspringt,
den Vorgang mit einer neuen Zündkerze
wiederholen.
Der Motor springt zwar an,
beschleunigt aber nicht korrekt,
bzw. funktioniert nicht korrekt mit
hoher Drehzahl.
Der Vergaser muss eingestellt
werden.
Vergaser bei einer autorisierten
Kundendienststelle einstellen lassen.
Der Motor erreicht die
Höchstgeschwindigkeit nicht
und/oder gibt übermäßig viel
Rauch ab.
1. Öl-/Benzingemisch
kontrollieren.
2. Luft lter verschmutzt.
3. Der Vergaser muss eingestellt
werden.
1. Frisches Benzin und geeignetes Motor
für 2-Takt-Motoren verwenden.
2. Reinigen; siehe Anleitungen im Kapitel
Wartung des Luftfilters.
3. Vergaser bei einer autorisierten
Kundendienststelle einstellen lassen.
Der Motor startet, dreht und
beschleunigt, hält aber die
Leerlaufdrehzahl nicht.
Der Vergaser muss eingestellt
werden.
Die Leerlaufschraube "T" (Abb.84, Seite 41)
im Uhrzeigersinn drehen, um die Drehzahl
zu erhöhen; siehe Kapitel Wartung des
Vergasers.
Schiene und Kette laufen beim
Betrieb heiß und rauchen
1. Kettenölbehälter leer
2. Zu feste Kettenspannung
3. Störung des Schmiersystems
1. Den Ölbehälter bei jedem Betanken
füllen.
2. Kettenspannung; siehe Anleitungen
im Kapitel Schienen-/Kettenmontage
(Seite 13).
3. 15-30 Sekunden lang auf Höchstdrehzahl
laufen lassen. Stoppen und überprüfen,
ob Öl von der Schienenspitze tropft.
Ist Öl vorhanden, liegt die Störung
möglicherweise an der lockeren Kette
oder der beschädigten Schiene. Ist kein
Öl vorhanden, wenden Sie sich an eine
autorisierte Servicestelle
Motor startet und läuft, aber die
Kette dreht nicht
1. Kettenbremse gezogen
2. Zu feste Kettenspannung
3. Schienen-/Kettenmontage
4. Kette bzw. Schiene beschädigt
5. Kupplung bzw. Ritzel
beschädigt
1. Kettenbremse lösen; siehe Kapitel
Gebrauch – Kettenbremse (Seite 27)
2. Kettenspannung; siehe Anleitungen
im Kapitel Schienen-/Kettenmontage
(Seite 13)
3. Siehe Anleitungen im Kapitel Schienen-/
Kettenmontage (Seite 13)
4. Siehe Anleitungen im Kapitel Schienen-
bzw. Kettenwartung (Seite 35)
5. Ggf. austauschen; wenden Sie sich an
eine autorisierte Servicestelle
ACHTUNG: Kette bei
laufendem Motor
niemals berühren
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco MT3500S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco MT3500S in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info