644122

Efco MT3500S Manual

30
Zoom out
Zoom in
Previous page
1/60
Next page
30
61 62
Italiano English Français
UTILIZZO USE UTILISATION
SRAMATURA
a) Partire sempre dal diametro maggiore andando verso la
punta per sramare la pianta o eventuali rami secondari.
b) Cercare sempre la posizione più stabile e sicura prima di
accelerare la motosega. Se occorre, mantenere l’equilibrio
appoggiando il ginocchio più vicino al tronco stesso.
c) Tenere la motosega appoggiata al tronco per non
affaticarsi eccessivamente, ruotandola sul lato sinistro
o destro a seconda della posizione del ramo da tagliare
(Fig. 61).
d) Nel caso di rami sotto tensione cercare una posizione
sicura per proteggersi dall’eventuale colpo di frusta.
Iniziare sempre il taglio dalla parte opposta alla piegatura.
ATTENZIONE - Non usare il bordo superiore della
punta della barra soprattutto per sramare perchè si
corre il rischio di ricevere un contraccolpo.
SEZIONATURA
Prima di iniziare a sezionare il tronco guardare come questo
è appoggiato al suolo; questo permetterà di tagliarlo nel
modo corretto evitando che la barra rimanga bloccata in
mezzo al tronco.
a) Iniziare a tagliare nella parte superiore per circa 1/3 del
diametro (1 - Fig. 62). Finire il taglio dalla parte inferiore
(2 - Fig. 62). In questo modo il taglio sarà perfetto e la
barra non rimarrà bloccata nel tronco.
b) Iniziare il taglio nella parte inferiore per circa 1/3 del
diametro (1 - Fig. 63). Finire il taglio dalla parte superiore
(2 - Fig. 63).
ATTENZIONE - Se il legno si chiude sulla catena
durante il taglio, fermare il motore, alzare il tronco
e cambiargli posizione (Fig. 64). Non cercare
di liberare la catena tirando l’impugnatura della
motosega.
LIMBING
a) Always start from the larger diameter and move towards
the tip to cut off limbs and any secondary branches.
b) Always find the safest and most stable position before
accelerating the chainsaw. If necessary, keep your balance
by resting your knee on the trunk itself.
c) Keep the chainsaw on the trunk so as not to get too tired,
turning it onto the left- or right-hand side depending on
the position of the branch to cut (Fig. 61).
d) In the case of branches under tension, find a safe position
to protect yourself if they whip back. Always start the cut
from the opposite side to the bend.
WARNING - Do not use the upper edge of the tip of
the guide bar to cross-cut; otherwise you might risk
a kickback.
BUCKING
When bucking up the trunk to desired lengths, there is one
basic rule to follow. Look to see where the trunk is supported,
and determine which way the two halves will fall when cut.
a) If the trunk is supported at both ends, first make a small
cut at the top (1 - Fig. 62), then complete the cut from the
bottom (2 - Fig. 62). This will avoid pinching the saw.
b) If the trunk is supported at one end or near the center,
first make a small cut from underneath (1 - Fig. 63), then
complete the cut from the top (2 - Fig. 63).
WARNING - If the saw becomes pinched in the trunk,
stop the engine, lift the log and change its position
(Fig. 64). Never attempt to free the saw by pulling on
it.
EBRANCHAGE
a) Commencez toujours par le diamètre le plus grand
en allant vers la pointe pour ébrancher la plante ou
d’éventuelles branches secondaires.
b) Cherchez toujours la position la plus stable et la plus sûre
avant d’accélérer la tronçonneuse. Maintenez l’équilibre,
s’il le faut, en appuyant le genou plus proche du tronc.
c) Tenez la tronçonneuse appuyée au tronc pour ne pas
trop vous fatiguer, en tournant sur le côté gauche ou sur
le côté droit suivant la position de la branche à couper
(Fig. 61).
d) Lorsque vous avez affaire à des branches sous tension,
cherchez une position sûre pour vous protéger
d’éventuels coups de fouet. Commencez toujours la
coupe du côté opposé au pli.
ATTENTION - N’utilisez pas le bord supérieur de la
pointe du guide, surtout pour ébrancher, parce que
vous courez le risque de recevoir un contrecoup.
DEBITAGE
Avant de commencer à débiter le tronc, vérifiez la façon
dont il est appuyé au sol. Ceci permet de le couper de façon
correcte en évitant ainsi que le guide reste coincé au milieu
du tronc.
a) Commencez à couper la partie supérieure pour environ
1/3 du diamètre (1-Fig. 62). Terminez la coupe par la partie
inférieure (2-Fig. 62). De cette façon la coupe sera parfaite
et le guide ne restera pas coincé dans le tronc.
b) Commencez à couper la partie inférieure pour environ 1/3
du diamètre (1-Fig. 63). Terminez la coupe par la partie
supérieure (2-Fig. 63).
ATTENTION - Si le guide coince dans une entaille,
arrêtez le moteur, soulevez le tronc et changez-le de
position (Fig. 64). Ne tentez pas de libérer la chaîne
en tirant sur la poignée de la tronçonneuse.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco MT3500S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco MT3500S in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info