644119
40
Zoom out
Zoom in
Previous page
1/202
Next page
36
I
GB
F
D
E
SK
P
GR
TR
CZ
RUS
UK
PL
13. TROUBLESHOOTING
WARNING: always stop the unit and disconnect the power cable from the mains before
carrying out any of the corrective checks recommended in the table below, except
when they require the unit to be in operation.
When you have checked all the possible causes listed and you are still experiencing the problem,
see your Servicing Dealer. If you are experiencing a problem that is not listed in this chart, see your
Servicing Dealer for service.
PROBLEM POSSIBLE CAUSE SOLUTION
The motor doesn't start or
runs unevenly. (Ensure
that the power cable is
connected to the mains)
1. Power cable damaged
2. Motor damaged
3. Brushes worn or
damaged
1. Replace: contact an Authorised Service
Centre
2. Replace: contact an Authorised Service
Centre
3. Replace: contact an Authorised Service
Centre
Engine does not reach full
speed.
1. Mains voltage and
frequency incorrect
2. Chain too taut
3. Length and section
of extension cable
incorrect
1. Check the mains rating information
2. Tension chain per instructions in
Operation-Chain Tension section
(Pag.26).
3. Recommended lengths for extension
cables (230V); see table in the Starting
section (Page 28)
Excessive sparking of the
brushes
Brushes worn or damaged Replace: contact an Authorised Service
Centre
Bar and Chain Running Hot
and Smoking
1. Chain oil tank empty.
2. Chain too taut
3. Oiler function.
1. Top up the oil reservoir.
2. Tension chain per instructions in
Operation-Chain Tension section
(Pag.26).
3. Run at full throttle 15 to 30 seconds.
Stop saw and check for oil dripping
from bar tip guard and guide bar. If oil is
present the chain may be dull or bar
may be damaged. If no oil contact a
Servicing Dealer.
Engine starts and runs, but
chain is not rotating
1. Chain too taut
3. Bar and chain assembly
incorrect
4. Chain and/or guide bar
damaged.
5. Rim sprocket damaged.
1. Tension chain per instructions in
Operation-Chain Tension section
(Pag.26).
3. Refer to Assembly-Assembling the Bar
and Chain Section (Pag.26).
4. Refer to Maintenance-Chain and/or
Maintenance-Guide Bar Section
(Pag.31).
5. Replace: contact an Authorised Service
Centre.
WARNING: Never
touch the chain
while the engine
is running.
40


Need help? Post your question in this forum.

Forumrules
1

Forum

efco-mt1800

Reset search

  • Efco MT1800 E giving trouble trying to switch on if I turn it on its side it starts but intermittent are new switches available and can I fit myself please Submitted on 22-5-2020 at 12:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco MT1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco MT1800 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info