644116
60
Zoom out
Zoom in
Previous page
1/68
Next page
60
Tabella di manutenzione
Le seguenti frequenze di manutenzione si riferiscono soltanto alle normali condizioni di utilizzo. Se l’uso giornaliero è più
lungo di quello normale o in presenza di condizioni di taglio avverse, le frequenze consigliate devono essere ravvicinate in
maniera appropriata
Unità intera
Ispezionare (perdite, incrinature e usura)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Pulire al termine del lavoro giornaliero
Veri  care il funzionamento
Ispezionare
Ispezionare (danni, a latura e usura)
A lare
Ispezionare (danni, usura e livello di ingrassaggio)
Pulire
Comandi (interruttore di massa, leva starter, leva
dell’acceleratore, leva di sicurezza)
Serbatoio del carburante
Filtro del carburante e tubi
Coppia conica
Campana della frizione
Protezione dell’apparato di taglio
Tutte le viti e i dadi accessibili (escluse le viti di registrazione)
Filtro dell’aria
Prima di
ciascun utilizzo
Mensilmente
In caso di danni o
malfunzionamento
In base alle
esigenze
6 mesi o 50 ore
1 anno o 100 ore
Feritoie del carter di avviamento
Fune di avviamento
Carburatore
Candela
Antivibranti
Dado e viti dellapparato di taglio
Pulire, sostituire l’elemento del  ltro
Ispezionare (danni e usura)
Sostituire
Ispezionare
Stringere nuovamente
Pulire
Pulire
Pulire al termine del lavoro giornaliero
Ispezionare (danni e usura)
Sostituire
Ispezionare (danni e usura)
Veri  care il serraggio di dadi e viti
Veri  care che il dado di  ssaggio dell’apparato di taglio sia
su cientemente serrato
Sostituire
Veri  care il minimo (l’apparato di taglio non
deve ruotare con motore al minimo)
Sostituire
Sostituire
Ispezionare (danni e usura)
Please note that the following maintenance intervals apply for normal operating conditions only. If your daily work requires
longer than normal or harsh cutting conditions are present, then the suggested intervals should be shortened accordingly.
Complete Machine
Inspect (Leaks, Cracks, and Wear)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Clean a er nishing daily work
Check Operation
Inspect (Leaks, Cracks, and Wear)
Inspect
Inspect (Damage, Sharpness, and Wear)
Inspect (Damage, Wear and Grease Level)
Clean
Controls (Ignition Switch, Choke Lever,  rottle
Trigger, Trigger interlock)
Fuel Tank
Fuel Filter and tube
Cutting Attachments
Cutting Attachments Guard
All Accessible Screws and Nuts (Not Adjusting Screws)
Air Filter
Before Each Use
Monthly
As Required
6 mouths or 50 hrs.
1 year or 100 hrs.
Cylinder Fins
Starter System Vents
Carburetor
Spark Plug
Vibration Mounts
Cutting Attachments nuts and screws
Cutting Attachments nuts and screws
Clean, Replace Filter Element
Check Tension
Replace
Inspect
Retighten
Clean
Clean
Clean a er nishing daily work
Replace
Check Electrode Gap
Inspect (Damage, and Wear)
Replace by Dealer
Check that nuts and screwx are tight
Check that the locking nut of the cutting
equipment is tighten correctly
Replace
Check Idle (Cutting Attachments must not
rotate at idle)
Replace
Replace
Inspect (Damage, and Wear)
x
x
Ispezionare (perdite, incrinature e usura)
Accessori di taglio
Veri  care la tensione
x
Alette del cilindro
Veri  care la distanza tra gli elettrodi
Sostituzione da parte del rivenditore
Tubi dellolio
Maintenance Chart
Sharpen
Bevel Gear
Clutch Drum
Inspect (Damage, Wear and Grease Level)
x
x
Inspect (Damage, and Wear)
Starter Rope
x
x
If Damaged or Faulty
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco DS2800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco DS2800 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info