644116

Efco DS2800 Manual

14
Zoom out
Zoom in
Previous page
1/68
Next page
14
Italiano FrançaisEnglish
ASSEMBLAGGIO ASSEMBLAGEASSEMBLY
MONTAGGIO PROTEZIONE SICUREZZA (Fig. 1)
Fissare la protezione (A) al tubo di trasmissione tramite
le viti (B), in una posizione che permetta di lavorare
in sicurezza.
NOTA: utilizzare la protezione (C, Fig. 1) solamente
con la testina a  li di nylon. La protezione (C) deve
essere  ssata con la vite (G) alla protezione (A).
MONTAGGIO DISCO (Fig. 2)
Allentare il dado (A) in senso orario; togliere la  angia
inferiore (E).Montare il disco (R) sulla  angia superiore
(F) assicurandosi del giusto senso di rotazione.
Fissare la flangia inferiore (E), e stringere il dado (A)
in senso antiorario.
Inserire il perno in dotazione (L), nell'apposito foro
(Fig. 2) per bloccare il disco e permettere il serraggio
del bullone (A, Fig. 2) a 2.5 kgm (25 Nm).
ATTENZIONE! - Non è previsto l’utilizzo di
queste macchine con il disco da legno (22-60-80 denti)
e relativa protezione metallica.
ATTENZIONE – Il collare (vedi frecce C, Fig.3)
deve posizionarsi nel foro di montaggio del disco.
MONTAGE PROTECTION-SECURITE (Fig. 1)
Fixer la protection (A) au tuyau de transmission à
l'aide des vis (B) en position telle à vous permettre de
travailler en toute sécurité.
NOTE: utiliser la protection (C, Fig.1) seulement
avec la tête l nylon. Le protecteur (C) doit être  xé
sur le carter de protection (A) au moyen de la vis (G).
MONTAGE DU DISQUE (Fig. 2)
Dévissez l’écrou (A) dans le sens horaire; otez la
bride inférieure (E). Montez le disque (R) sur la bride
supérieure (F), en véri ant le bon sens de rotation.
Montez la bride inférieure (E), et vissez l’écrou (A)
dans le sens anti-horaire.
En lez le goujon en dotation (L) dans le trou approprié
(Fig. 2) pour pouvoir bloquer le disque et serrer le
boulon (A, Fig. 2) à 2.5 kgm (25 Nm).
ATTENTION! Ce machine n’est pas destinée à
un usage avec disques à bois (22-60-80 dents), et la
protection metallique relative.
ATTENTION – Installer le collier (voir  èches
C, Fig.3) dans l’ori ce de montage du disque.
FITTING THE SAFETY GUARD (Fig. 1)
Fit the blade guard (A) to the sha arm with screws
in a position allowing the operator to work safely (B).
NOTE: use the guard (C, Fig. 1) only with nylon head.
Secure the guard (C) to the protection (A) by means
of the screw (G).
FITTING THE BLADE (Fig. 2)
Loosen the nut (A) clockwise; remove lower  ange (E).
Fix the blade (R) onto the upper  ange (F) making sure
that the rotation direction is correct.
Fix the lower flange (E), and tighten nut (A) counter-
clockwise.
Put the pin provided (L) in the appropriate hole (Fig.
2) to block the blade and allow the bolt (A, Fig. 2) to
be tightened to 2.5 kgm (25 Nm).
WARNING! is machine is not suitable for use
with blade for wood (22-60-80 teeth) and relevant metal
guard.
WARNING – Collar (see arrows C, Fig.3) must
locate in blade’s mounting hole.
1
2 3
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco DS2800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco DS2800 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info