644150
55
Zoom out
Zoom in
Previous page
1/60
Next page
55
RISOLUZIONE DEI PROBLEMI
ATTENZIONE: fermare sempre l’unità e scollegare la candela prima di effettuare
tutte le azioni correttive raccomandato nella tabella sottostante, tranne che
venga richiesto il funzionamento dell’unità.
Quando si sono verificate tutte le possibili cause e il problema non è risolto, consultare un
Centro Assistenza Autorizzato. Se si verifica un problema che non è elencato in questa tabella,
consultare un Centro Assistenza Autorizzato.
PROBLEMA POSSIBILI CAUSE SOLUZIONE
Il motore non si avvia o si
spegne solo dopo pochi
secondi dall’avvio. (Assicurarsi
che l’interruttore sia in
posizione “I”)
1. Non c’è scintilla.
2. Motore ingolfato.
1. Controllare la scintilla della candela.
Se non c’è la scintilla, ripetere il test
con una candela nuova (CMR7H).
2. Seguire la procedura di pag.22. Se il
motore non si avvia ancora, ripetere
la procedura con una candela
nuova.
Il motore parte, ma non
accelera correttamente o non
funziona correttamente ad
alta velocità.
Il carburatore deve essere
regolato.
Contattare un Centro Assistenza
Autorizzato per regolare il carburatore.
Il motore non raggiunge la
piena velocità e / o emette
fumo eccessivo.
1. Controllare la miscela
olio / benzina.
2. Filtro aria sporco.
3. Il carburatore deve essere
regolato.
1. Utilizzare benzina fresca e un olio
adeguato per motore 2 tempi.
2. Pulire: vedi le istruzioni nel capitolo
Manutenzione filtro aria.
3. Contattare un Centro Assistenza
Autorizzato per regolare il
carburatore.
Il motore si avvia, gira e
accelera, ma non tiene il
minimo.
Il carburatore deve essere
regolato.
Regolare la vite del minimo T”
(Fig.81, pag.40) in senso orario per
aumentare la velocità; vedere capitolo
Manutenzione carburatore.
Il motore parte e funziona, ma
la lama non si muove
1. Montaggio lama non
corretto
2. Lama danneggiata
3. Frizione o albero di
trasmissione danneggiato
1. Contattare un Centro Assistenza
Autorizzato
2. Contattare un Centro Assistenza
Autorizzato
3. Contattare un Centro Assistenza
Autorizzato
Attenzione: non
toccare mai la lama
quando il motore è
in funzione.
TROUBLESHOOTING CHART
WARNING: Always stop unit and disconnect spark plug before performing all of
the recommended remedies below except remedies that require operation of the
unit.
When you have checked all the possible causes listed and you are still experiencing the
problem, see your Servicing Dealer. If you are experiencing a problem that is not listed in this
chart, see your Servicing Dealer for service.
PROBLEM POSSIBLE CAUSE SOLUTION
Engine will not start or will
run only a few seconds after
starting.
(Make sure Ignition switch is
in start position “I”)
1. No spark
2. Flooded engine.
1. Watch for spark at spark plug tip. If
there is no spark, repeat test with a
new spark plug (CMR7H).
2. Follow procedure page 22 If engine
still fails to start, repeat procedure
with a new spark plug.
Engine starts but will not
accelerate properly or will not
run properly at high speed.
Carburetor requires
adjustment.
Contact a Servicing Dealer for
carburetor adjustment.
Engine does not reach full
speed and / or emits excessive
smoke
1. Check oil fuel mixture.
2. Air filter dirty.
3. Carburetor requires
adjustment.
1. Use fresh fuel and the correct
2-cycle oil mix.
2. Clean per instruction in
Maintenance-Air Filter Section.
3. Contact a Servicing Dealer for
carburetor adjustment.
Engine starts, runs and
accelerates but will not idle.
Carburetor requires
adjustment.
Turn idle speed screw “T” (Fig. 81,
pag. 40) clockwise to increase idle
speed.See Operation-Carburetor
Adjustment.
The engine starts and runs,
but the blade doesn't move
1. Blade incorrectly fitted
2. Blade damaged
3. Clutch or transmission shaft
damaged
1. Contact an Authorised Service
Centre
2. Contact an Authorised Service
Centre
3. Contact an Authorised Service
Centre
Warning: never
touch the blade
when the engine is
running.
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Efco BC240HL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Efco BC240HL in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Efco BC240HL

Efco BC240HL User Manual - Dutch, Swedish - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info