516135
18
Zoom out
Zoom in
Previous page
1/31
Next page
Parameter Description
Authentication Type
There are two authentication types: “Open System” and “Shared Key”.
When you select “Open System”, wireless stations can associate with this
access point without WEP encryption. When you select “Shared Key”, you
should also setup WEP key in the “Encryption” page and wireless stations
should use WEP encryption in the authentication phase to associate with
this access point. If you select “Auto”, the wireless client can associate with
this access point by using any one of these two authentication types.
Fragment Threshold
“Fragment Threshold” specifies the maximum size of packet during the
fragmentation of data to be transmitted. If you set this value too low, it will
result in bad performance.
RTS Threshold
When the packet size is smaller than the RTS threshold, the access point
will not use the RTS/CTS mechanism to send this packet.
Beacon Interval
The interval of time that this access point broadcast a beacon. Beacon is
used to synchronize the wireless network.
Data Rate
The “Data Rate” is the rate this access point uses to transmit data packets.
The access point will use the highest possible selected transmission rate to
transmit the data packets.
Preamble Type
Preamble type defines the length of CRC block in the frames during the
wireless communication. “Short Preamble” is suitable for high traffic
wireless network. “Long Preamble” can provide more reliable
communication.
Broadcast ESSID
If you enable “Broadcast ESSID”, every wireless station located within the
coverage of this access point can discover this access point easily. If you
are building a public wireless network, enabling this feature is
recommended. Disabling “Broadcast ESSID” can provide better security.
IAPP
If you enable “IAPP”, the access point will automatically broadcast
information of associated wireless stations to its neighbors. This will help
wireless station roaming smoothly between access points. If you have more
than one access points in your wireless LAN and wireless stations have
roaming requirements, enabling this feature is recommended. Disabling
“IAPP” can provide better security.
802.11g Protection
This is also called CTS Protection. It is recommended to enable the
protection mechanism. This mechanism can decrease the rate of data
collision between 802.11b and 802.11g wireless stations. When the
protection mode is enabled, the throughput of the AP will be a little lower
due to many of frame traffic should be transmitted.
Click Apply button at the bottom of the screen to save the above configurations. You can now configure
other advance sections or start using the Access Point.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edimax EW-7209APg at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edimax EW-7209APg in the language / languages: English as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info