Manual Edilkamin Windo 3 - 50 (page 18 of 24) (English)

810873

Zoom out

Zoom in

1/24

ENGLISH

Lighting a cold fireplaceLighting a cold fireplace

1. Check the existing ash bed is not too high. If the 1. Check the existing ash bed is not too high. If the

ash bed is too high, there is a danger of opening the ash bed is too high, there is a danger of opening the

door of the fireplace to add wood and possible brazier door of the fireplace to add wood and possible brazier

fragments fall out of the fireplace.fragments fall out of the fireplace.

2. Position the adjustment lever of the valve in the “total 2. Position the adjustment lever of the valve in the “total

opening” position . The air for combustion will flow opening” position . The air for combustion will flow

intensely to the wood in the fireplace, to quickly reach intensely to the wood in the fireplace, to quickly reach

good combustion.good combustion.

3. place the wood in the fireplace without excessively 3. place the wood in the fireplace without excessively

squashing it in. Position a firelighter between the wood squashing it in. Position a firelighter between the wood

logs and light. Never user materials such as petrol, logs and light. Never user materials such as petrol,

alcohol and similar to switch on.alcohol and similar to switch on.

4. At this point, close the door and monitor it for a few 4. At this point, close the door and monitor it for a few

minutes. If the fire should extinguish, slowly open the minutes. If the fire should extinguish, slowly open the

door, re-position another firelighter between the logs door, re-position another firelighter between the logs

and light again.and light again.

Lighting a hot fireplace Lighting a hot fireplace

When should wood be added? When the fuel is almost When should wood be added? When the fuel is almost

completely consumed to embers. With the glove, completely consumed to embers. With the glove,

slowly open (to avoid formation of vortexes that can slowly open (to avoid formation of vortexes that can

cause smoke to exit) the door. Add the desired wood to cause smoke to exit) the door. Add the desired wood to

the fireplace, locating it on the existing embers (within the fireplace, locating it on the existing embers (within

the quality limits indicated in the technical table). the quality limits indicated in the technical table).

Product functioning changes with the chimney flue Product functioning changes with the chimney flue

draft and adjustment of the air valve in combustion.draft and adjustment of the air valve in combustion.

Functioning with initial low draftFunctioning with initial low draft

To extract air for combustion and discharge the To extract air for combustion and discharge the

smoke, the fireplace needs a draft to be exerted on the smoke, the fireplace needs a draft to be exerted on the

chimney flue. chimney flue.

If the draft is weak, initially light a “starter” fire using If the draft is weak, initially light a “starter” fire using

small sized lighting material. small sized lighting material.

Once the correct draft is restored, you can add the fuel.Once the correct draft is restored, you can add the fuel.

As with all the products, the wood product heats and As with all the products, the wood product heats and

cools during the various phases. This would lead to cools during the various phases. This would lead to

normal dilation. Such dilation can cause slight settling normal dilation. Such dilation can cause slight settling

noise, which is not a reason for dispute.noise, which is not a reason for dispute.

INSTRUCTIONS FOR USE

FUEL

The product was designed to burn wooden logs or

sawdust briquettes.

Use dry wood logs (max. humidity 20%)Use logs The

use of damp wood would cause the product and the

flue to get dirty, the risk of smoke and a lower yield

than that declared.Each type of wood has different

characteristics that also influence combustion yield.

The data outlined on this manual are with wood used

during certification.

In general wood can have a heat of combustion up to

4.5 kWh/kg while cut fresh it has heat of combustion

around 2 kWh/kg

In general, beech or elm is recommended, or however

class A1 wood according to UNI EN ISO 17225-5

Attention to prolonged use of wood with aromatic oils

(e.g. eucalyptus). Cast iron parts can deteriorate

Use the recommended quantities of wood:

Overloading causes overheating, resulting in damage:

• possible deformation of the inner parts;

• possible irreversible changes to the colour of the

paint on the metal parts for which Edilkamin or the

retailer cannot be held liable.

To respect the environment and safety, do NOT burn,

among other things: plastic, varnished wood, coal and

bark waste. Do not use the product as an incinerator.

Use of these fuels also nullifies the guarantee.

First switch on phases

• Ensure you have read and understood the content

of this manual

• • Remove all the inflammable parts from the product Remove all the inflammable parts from the product

(manuals, labels, etc.). In particular remove any (manuals, labels, etc.). In particular remove any

labels from the glass. If they melt, they would labels from the glass. If they melt, they would

irreversibly damage the glass. irreversibly damage the glass.

For initial switch on of the fireplace, always use the For initial switch on of the fireplace, always use the

smallest logs. Use larger wooden logs to raise the fire. smallest logs. Use larger wooden logs to raise the fire.

Always locate the wood deep in the fireplace.Always locate the wood deep in the fireplace.

There may be a slight smell of paint the first few times it

is ignited, however, this will disappear quickly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Windo 3 - 50 in the language / languages: English as an attachment in your email.

The manual is 2.25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Windo 3 - 50

Edilkamin Windo 3 - 50 Usermanual and installation guide - German - 20 pages

Edilkamin Windo 3 - 50 Usermanual and installation guide - French, Italian - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin Windo 3 - 50 Manual

Product: