810840

Edilkamin Tally Up S Evo Manual

35
Zoom out
Zoom in
Previous page
1/40
Next page
ENGLISH
Lighting a hot fireplace
When should wood be added? When the fuel is
almost completely consumed to embers. With the
glove supplied, slowly open (to avoid formation of
vortexes that can cause smoke to exit) the door. Add
the desired wood to the fireplace, locating it on the
existing embers (within the quality limits indicated in
the technical table).
Stove functioning changes with the chimney flue draft
and adjustment of the air valve in combustion.
Functioning with initial low draft
To extract air for combustion and discharge the
smoke, the fireplace needs a draft to be exerted on the
chimney flue.
If the draft is weak, initially light a “starter” fire using
small sized lighting material.
Once the correct draft is restored, you can add the fuel.
As with all the products, the wood stove heats and
cools during the various phases. This would lead to
normal dilation. Such dilation can cause slight settling
noise, which is not a reason for dispute.
The hot air reaches the premises with natural motion
(natural convection) without the help of a fan.The
retailer also offers an Air Diffuser kit with fans to
distribute the hot air in the premises.
NOTE FOR UK
Refuelling on to a low fire bed
If there is insufficient burning material in the firebed to
light a new fuel charge, excessive smoke emission can
occur. Refuelling must be carried out onto a sufficient
quantity of glowing embers and ash that the new fuel
charge will ignite in a reasonable period. If there are
too few embers in the fire bed, add suitable kindling to
prevent excessive smoke
Fuel overloading
The maximum amount of fuel specified in this manual
should not be exceeded, overloading can cause
excess smoke.
ISTRUCTIONS FOR USE
First switch on phases
•Ensure you have read and understood the content
of this manual
•Remove all the inflammable parts from the product
(manuals, labels, etc.). In particular remove any
labels from the glass. If they melt, they would
irreversibly damage the glass.
For initial switch on of the fireplace, always use the
smallest logs. Use larger wooden logs to raise the fire.
Always locate the wood deep in the fireplace, almost in
contact with the rear wall, so that even if they slide they
won’t come in contact with the glass.
There may be a slight smell of paint the first few times it
is ignited, however, this will disappear quickly.
Lighting a cold fireplace
1. Check the existing ash bed is not too high. If the
ash bed is too high, there is a danger of opening the
door of the fireplace to add wood and possible brazier
fragments fall out of the fireplace.
2. Position the adjustment lever of the valve in the “total
opening” position. The air for combustion will flow
intensely to the wood in the fireplace, to quickly reach
good combustion.
3. place the wood in the fireplace without excessively
squashing it in. Position a firelighter between the wood
logs and light. Never user materials such as petrol,
alcohol and similar to switch on.
4. At this point, close the door and monitor it for a few
minutes. If the fire should extinguish, slowly open the
door, re-position another firelighter between the logs
and light again.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Tally Up S Evo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Tally Up S Evo in the language / languages: English as an attachment in your email.

The manual is 22.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Tally Up S Evo

Edilkamin Tally Up S Evo Usermanual and installation guide - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info