810862

Edilkamin Screen Evo 80-2 Manual

23
Zoom out
Zoom in
Previous page
1/28
Next page
23
ENGLISH
Lighting a cold fireplace
1. Check the existing ash bed is not too high. If the
ash bed is too high, there is a danger of opening the
door of the fireplace to add wood and possible brazier
fragments fall out of the fireplace.
2. Position the adjustment lever of the valve in the “total
opening” position . The air for combustion will flow
intensely to the wood in the fireplace, to quickly reach
good combustion.
3. place the wood in the fireplace without excessively
squashing it in. Position a firelighter between the wood
logs and light. Never user materials such as petrol,
alcohol and similar to switch on.
4. At this point, close the door and monitor it for a few
minutes. If the fire should extinguish, slowly open the
door, re-position another firelighter between the logs
and light again.
Lighting a hot fireplace
When should wood be added? When the fuel is
almost completely consumed to embers. With the
glove supplied, slowly open (to avoid formation of
vortexes that can cause smoke to exit) the door. Add
the desired wood to the fireplace, locating it on the
existing embers (within the quality limits indicated in
the technical table).
Product functioning changes with the chimney flue
draft and adjustment of the air valve in combustion.
Functioning with initial low draft
To extract air for combustion and discharge the
smoke, the fireplace needs a draft to be exerted on the
chimney flue.
If the draft is weak, initially light a “starter” fire using
small sized lighting material.
Once the correct draft is restored, you can add the fuel.
As with all the products, the wood product heats and
cools during the various phases. This would lead to
normal dilation. Such dilation can cause slight settling
noise, which is not a reason for dispute.
INSTRUCTIONS FOR USE
FUEL
The product was designed to burn wooden logs or
sawdust briquettes.
Use dry wood logs (max. humidity 20%)Use logs The
use of damp wood would cause the product and the
flue to get dirty, the risk of smoke and a lower yield
than that declared.Each type of wood has different
characteristics that also influence combustion yield.
The data outlined on this manual are with wood used
during certification.
In general wood can have a heat of combustion up to
4.5 kWh/kg while cut fresh it has heat of combustion
around 2 kWh/kg
In general, beech or elm is recommended, or however
class A1 wood according to UNI EN ISO 17225-5
Attention to prolonged use of wood with aromatic oils
(e.g. eucalyptus). Cast iron parts can deteriorate
Use the recommended quantities of wood:
Overloading causes overheating, resulting in damage:
• possible deformation of the inner parts;
• possible irreversible changes to the colour of the
paint on the metal parts for which Edilkamin or the
retailer cannot be held liable.
To respect the environment and safety, do NOT burn,
among other things: plastic, varnished wood, coal and
bark waste. Do not use the product as an incinerator.
Use of these fuels also nullifies the guarantee.
First switch on phases
• Ensure you have read and understood the content
of this manual
• Remove all the inflammable parts from the product
(manuals, labels, etc.). In particular remove any
labels from the glass. If they melt, they would
irreversibly damage the glass.
For initial switch on of the fireplace, always use the
smallest logs. Use larger wooden logs to raise the fire.
Always locate the wood deep in the fireplace, almost in
contact with the rear wall, so that even if they slide they
won’t come in contact with the glass.
There may be a slight smell of paint the first few times it
is ignited, however, this will disappear quickly.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Screen Evo 80-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Screen Evo 80-2 in the language / languages: English as an attachment in your email.

The manual is 6.22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Screen Evo 80-2

Edilkamin Screen Evo 80-2 Usermanual and installation guide - French, Italian - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info