Manual Edilkamin Nea (page 23 of 153) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish)

810803

Zoom out

Zoom in

1/153

- 23 -

ENGLISH

INSTALLATION

SMOKE OUTLET

The stove must have its own smoke outlet (the smoke can-

not be discharged into a smoke ﬂ ue used by other devices).

The smoke is discharged through the 8 cm diameter outlet at

the back of the stove. The smoke outlet must be connected to

outside by means of suitable steel pipes EN 1856 certiﬁ ed.

The pipe must be hermetically sealed.

The material used to seal and if necessary insulate the pipes,

must be resistant to high temperatures (high temperature silico-

ne or mastic). The only horizontal section allowed may be up

to 2 m long up to three 90° bends (in relation to the vertical).

A vertical section of at least 1.5m and an anti-wind terminal

is necessary (if the discharge outlet is not in a chimney ﬂ ue

reference UNI 10683).

The vertical duct can be internal or external. If the smoke chan-

nel is outside, it must be appropriately insulated. If the smoke

channel is ﬁ tted inside a chimney ﬂ ue, the latter must be suita-

ble for solid fuel. If it is wider than 150 mm in diameter it must

be improved by entering a pipe that has a suitable cross-section

and is made of suitable material (e.g. 80 mm diameter steel).

All sections of the smoke duct must be accessible for inspec-

tion. The chimney pots and smoke ducts connected to the solid

fuel appliances must be cleaned once a year (verify whether a

speciﬁ c legislation exists in your country).

Failure to regularly inspect and clean the stove increases the

probability of a ﬁ re occurring in the chimney pot. In that case,

proceed as follows: Do not use water to extinguish the ﬁ re;

Empty the pellet hopper; Contact specialist personnel before

reigniting the stove.

The stove is designed to work under any weather conditions.

In case of particular conditions, such as strong wind, the safety

system may be activated, which results in the stove being

extinguished. If this happens, do not operate the stove with

the safety devices disabled. If the problem persists, contact our

Technical Service Department.

All local and national laws and European standards must be

met when installing and using the appliance. In Italy, refer

to the UNI 10683 standard, as well as any regional or local

health-authority regulations.

It is necessary to refer to regulations in force in each country. If

installing in an apartment building, check with the management

company ﬁ rst.

VERIFY COMPATIBILITY WITH OTHER DEVICES

In Italy the stove MUST NOT be installed in the same space

as type B gas heating equipment (e.g. gas boilers, stoves, and

equipment served by an extraction hood) as the stove may cau-

se a vacuum in the space which may compromise or inﬂ uence

how these units work. Pursuant to standard UNI 10683, the

stove can also be installed in a bedroom.

VERIFYTHE POWER SUPPLY CONNECTION

(the plug must be accessible)

The stove is supplied with a power cable that is to be connected

to a 230V 50 Hz socket, preferably ﬁ tted with a magnetother-

mic switch. Voltage variations exceeding 10% can damage

the stove (unless already installed, an appropriate differential

switch must be ﬁ tted). The electrical system must comply

with the law; particularly verify the efﬁ ciency of the earthing

system. The power line must have a suitable cross-section for

the stove’s power. An inadequate earthing system can cause

anomalies for which Edilkamin cannot be held liable.

POSITIONING

The stove must be level for it to function correctly.

Verify the bearing capacity of the ﬂ oor.

FIRE PREVENTION SAFETY DISTANCES

The stove must be installed in compliance with the following

safety conditions:

- minimum distance from ﬂ ammable materials around the sides

and back of the stove: 20 cm

- ﬂ ammable materials must not be placed less than 80 cm from

the front of the stove.

If it is not possible to comply with the above-mentioned di-

stances, technical and construction-related provisions must be

taken to prevent ﬁ re hazards.

If connected to wooden walls or other ﬂ ammable materials, the

smoke exhaust pipe must be insulated.

AIR INTAKE

The stove is also suitable for installation in houses deﬁ ned as

“passive”. In this case, the air for combustion must be taken

by connecting (hermetically) the input vent at the back of the

stove with the external environment by means of a ø 4 cm pipe.

Make sure that the external air intake is positioned so that it

cannot be obstructed.

In all other types of houses, the stove can be installed in the

traditional manner and therefore also using the air of the

environment in which it is placed (in any case, the technical

standards of reference must always be respected).

The pipe must be less than 1 metre long and have no bends.

It must end with a section at 90° facing downwards or be ﬁ tted

with a wind guard. in any case the air-intake duct must be a

free section of at least 12 cm². The external terminal of the air

inlet channel must be protected with an anti-insect netting that

does not reduce the 12 cm² through passage.

inspection

A: insulated steel ﬂ ue

B: minimum height of 1.5 m and in any case above the height of the

roof gutter

C-E: air intake from inside room (minimum internal section: 80 cm²)

D: steel ﬂ ue, inside existing brick-built chimney.

CHIMNEY POT

The main characteristics are:

- an internal cross-section at the base, which is the same as that

of the chimney ﬂ ue

- an outlet cross-section which is no smaller than twice that of

the chimney ﬂ ue

- its position must be high enough to catch the wind and avoid

downdraft areas in turbulent wind, it must be high enough to

catch the wind and avoid downdraft areas in turbulent wind.

TYPICAL EXAMPLES

Fig. 1 Fig. 2

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Nea in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 4.65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin Nea Manual

Product: