810916

Edilkamin Meg Manual

30
Zoom out
Zoom in
Previous page
1/178
Next page
- 30 -
ENGLISH
Pump (circulator)
“Pushes” water toward the heating system.
Closed expansion tank
“absorbs” the variations in the volume of water contained insi-
de the boiler-stove due to the heating effect.
Aheating technician must evaluate the need to add a second
tank to the existing one, depending on total amount of wa-
ter in the system.
Gear motor
This activates the screw allowing the transport of the pellets
from the hopper to the chamber.
Manometer
Positioned on the back of the thermo stove
(B -fi g. 1), it allows
water pressure to be read. When the thermo stove is running,
the recommended pressure is 1,5 bar.
Drain tap
Positioned on the back of the thermo stove, low down. It must be
opened if the water the unit contains needs to be drained.
Venting valve
Positioned in the upper part under the front-top grill (see page
36 fi g. 2), it allows for any air present during the loading of the
water into the stove to be bled off.
Smoke thermocouple
on the smoke outlet. It reads the smoke temperature. It regula-
tes the ignition stage and shuts the boiler-fi replace down if the
temperature is too high or too low.
Flow sensor
located in the extraction duct, is activated and shuts down the
thermo stove when the fl ow of combustion air is incorrect,
which means a resulting risk of low pressure problems in the
smoke circuit.
Feed Screw safety thermostat
Placed near the pellet hopper. It disconnects the electrical sup-
ply to the gear motor if the temperature detected is too high.
Water temperature detector
It reads the water temperature in the boiler and sends the circuit
board information for pump management and boiler power
modulation.
If the temperature is too high, it starts a shutdown.
Water overheating safety thermostat
detects the water temperature in the thermo-stoves. If this is
too high, it triggers the shutdown process by disconnecting the
electrical supply to the gear motor. If the thermostat has trigge-
red a reaction, it must be reset by means of the red emergency
button at the back of the stove (A - fi g. 1).
Overpressure valve 3 bar
Upon reaching the pressure stipulated on the plate, the system
is triggered to discharge the water and consequently the water
must be topped up.
WARNING!!!! remember to carry out the connection with
the sewage system.
Electric coil
It sets off of the combustion of the pellets and it remains lit until
the fl ame has been ignited. This component is subject to wear.
Pressure switch
Positioned in the fume-aspiration area, it is triggered in the case
of a depression in the fumes circuit (e.g. obstructed fl ue) and
interrupts the movement of the pellets. It blocks pellet loading
causing the stove to go out.
Vacuum gauge (electronic pressure sensor):
positioned on the smoke extractor, which detects the vacuum
value (compared to the installation environment) in the combu-
stion chamber.
Tank safety thermostat:
Located on the system that loads the pellets from the hopper.
Trips when the temperature inside the boiler-stove is too high.
It stops pellet loading, causing the boiler-stove to go out.
FEATURES
• COMPONENTS - SAFETY AND DETECTION DEVICES
N.B.:
IF THE BOILER-STOVE BLOCKS, THE REASON WILL APPEAR ON THE DISPLAY AND THIS WILL BE SAVED.
B
A
fi g. 1
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Meg at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Meg in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 8.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info