Manual Edilkamin marea (page 20 of 77) (English, German, Dutch, French, Italian)

496602

Zoom out

Zoom in

1/77

- 20 -

ENGLISH

THE INTERFACE DISPLAY

The panel consists of a display and 4 keys:

0/1 : to ignite and shutdown the stove

Menù: to access the menu

+/- to increase / deincrease the various settings

FUNCTIONS

Before igniting the stove.

1st Ignition: contact the DEALER, for the stove to be calibrated according to the type of pellets used and conditions it is used in.

A slight smell of paint may be noticed during the rst few times it is ignited, however, this only lasts a short while.

Before igniting the stove you must verify:

• that the stove has been installed correctly (refer to pgs. 17-18);

• the electrical power supply;

• that the door is closed;

• that the combustion chamber is clean;

• that the display is on standby (the power or temperature ashes).

You can then press the ON/OFF key for at least 2 seconds and the stove will automatically drop pellets to start the combustion

process and ‘Start’ will appear on the display with a countdown in seconds (1020). There is no preset time for the ignition

process: it can take less than 17 minutes if the smoke temperature is reached before.

LOADING THE FEED SCREW.

To re-ll the pellet storage hopper when it is empty press the + and – keys simultaneously.

If the stove has shutdown because the pellets have nished, the pellet storage hopper must be relled before igniting the stove.

It is normal for some pellets to remain in the hopper, which the feed screw is unable to pick up.

IGNITING THE STOVE

Automatic ignition

With the stove on standby, press the 0/1 key for 2 seconds for the ignition process to start. ‘Start’ will appear on the display for

17 minutes (there is no preset time for the ignition process: this will be automatically shortened if the control board detects that

certain tests have been carried out positively). The ame appears after about 5 minutes.

Manual ignition

At a temperature lower than 3° C – too low for the electrical resistance to become red-hot – or if the resistance is temporarily

not working, you can use a relighter to ignite the stove.

Place a well-lit relighter into the combustion chamber, close the door and press the 0/1 key on the synoptic panel or the

remote control.

FUNCTION MODE

Manual mode

With the stove on, press the ‘Menu’ key to enable the manual mode and the ventilation will be enabled accordingly (the power

can be adjusted from P1 to P3 with the + and - keys).

Adjusting the ventilation

With the stove on, press the ‘Menu’ key again to adjust the ventilation with the + and – keys (9 levels, split three by three and

associated with the power levels).

The ventilation can only be adjusted when in manual mode.

Automatic mode

Press the ‘Menu’ key again to switch to automatic mode (the temperature ranges from 5° to 35° C and can be adjusted with the

+ and - keys). You must set the desired room temperature and the stove adjusts the power to reach (P3) or maintain (P1) the

desired temperature.

If the temperature is set lower than that of the room, the stove will operate at P1, utilising the relevant amount of pellets (0,7 Kg/h).

Switching the stove off

With the stove on, press the 0/1 key for 2 seconds to start the shutdown process. A countdown from 60 to 0 will appear on the

display and it will last 10 minutes.

During the shutdown process:

• pellet loading ceases

• ventilation increases to maximum

• the smoke extraction motor increases to maximum

Never unplug the stove during the shutdown process.

You will help keep the stove clean by moving the cleaning rods that scrape the smoke pipe during the shutdown process.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin marea in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin marea Manual

Product: