810792
21
Zoom out
Zoom in
Previous page
1/146
Next page
- 21 -
ENGLISH
SAFETY INFORMATION
The LOGO stove is designed to heat, through automatic pellet
combustion in the hearth, the room where it is installed, both
by radiation and the air that comes out of the front grille.
• The only risks that may derive from using the stove pertain
to non-compliance with installation instructions, direct contact
with live electrical parts (internal), contact with the Ŏ re or hot
parts (glass, pipes, hot air output), or foreign substances being
put in the stove.
• Only use wood pellets as fuel.
• Should components fail, the stoves are equipped with safety
devices that guarantee automatic shutdown. These are activated
without any intervention required.
• In order to function correctly, the stove must be installed in
accordance with the instructions given herein and the door
must not be opened during operation: combustion is fully
automatic and requires no intervention.
• Under no circumstances should any foreign substances be
entered into the hearth or hopper.
• Do not use ŏ ammable products to clean the smoke channel
(the ŏ ue section connecting the stove smoke outlet to the
chimney ŏ ue).
• The hearth and hopper parts must only be cleaned when
COLD.
• The glass can be cleaned when COLD with a suitable product
(e.g. GlassKamin Edilkamin) and a cloth.
• Do not clean when hot.
• Make sure the stove is installed and ignited the Ŏ rst time
by Edilkamin-qualiŎ ed CAT personnel (technical assistan-
ce centre) in accordance with the instructions provided here
within; this is an essential requirement for the validation of the
guarantee.
• When the stove is in operation, the exhaust pipes and door
become very hot (do not touch without wearing the thermal
glove).
• Do not place anything, which is not heat resistant near the
stove.
• NEVER use liquid fuel to ignite the stove or rekindle the
embers.
• Do not obstruct the ventilation apertures in the room where
the stove is installed, nor the air inlets of the stove itself.
• Do not wet the stove and do not go near electrical parts
with wet hands.
• Do not use reducers on the smoke exhaust pipes.
• The stove must be installed in a room that is suitable for
Ŏ re prevention and equipped with all that is required (power
and air supply and outlets) for the stove to function correctly
and safely.
Should ignition fail, DO NOT re-ignite until you have
emptied the combustion chamber.
•ATTENTION: THE PELLET EMPTIED FROM THE
COMBUSTION CHAMBER MUST NOT BE DEPOSI-
TED INSIDE THE HOPPER.
PRINCIPLE OF OPERATION
The LOGO stove produces hot air using wood pellets as fuel,
with electronically controlled combustion. Hereunder is the
explanation of its functions (the letters refer to Ŏ gure 1).
The fuel (pellets) is provided by the storage hopper (A) and,
to the combustion chamber (D) by means of a feed screw (B),
which is driven by a gear motor (C).
The pellets are ignited by the air that is heated by an electrical
resistance (E) and drawn into the combustion chamber
by a smoke extractor (F).
The fumes produced during the combustion process are ex-
tracted from the hearth by the same centrifugal fan (F) and
expelled through the outlet (G) located on the lower part at the
back of the stove.
The hearth is covered in cast iron, and closed frontally by a
glass ceramic door (to open use the dedicated “cold hand”
handle”).
Fuel quantity, smoke extraction and combustion air supply
are all controlled by an electronic control board, which is
equipped with Leonardo® software to achieve high combustion
efŎ ciency and low emissions.
The synoptic panel (M) is installed on the top, through which
all phases of operation can be displayed and controlled.
The main phases can be controlled via the optionally supplied
remote control.
The main functions can also be controlled by remote control.
Aserial port is found at the back of the stove (optional cable:
code 640560) to be connected to devices that allow remote
ignition (e.g. remote telephone, local thermostat).
A
B
C
D
E
F
G
M
Ŏ g. 1
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Logo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Logo in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info