810853

Edilkamin Firebox Riga Manual

19
Zoom out
Zoom in
Previous page
1/24
Next page
19
ENGLISH
Lighting a cold fifi replace
1. Check the existing ash bed is not too high. If the
ash bed is too high, there is a danger of opening the
door of the fifi replace to add wood and possible
brazier fragments fall out of the fifi replace.
2. Position the adjustment lever of the valve in the “total
opening” position . The air for combustion will flfl ow
intensely to the wood in the fifi replace, to quickly reach
good combustion.
3. place the wood in the fifi replace without excessively
squashing it in. Position a fifi relighter between the
wood logs and light. Never user materials such as
petrol, alcohol and similar to switch on.
4. At this point, close the door and monitor it for a few
minutes. If the fifi re should extinguish, slowly open the
door, re-position another fifi relighter between the logs
and light again.
Lighting a hot fireplace
When should wood be added? When the fuel is
almost completely consumed to embers. With the
glove supplied, slowly open (to avoid formation of
vortexes that can cause smoke to exit) the door.
Add the desired wood to the fifi replace, locating it on
the existing embers (within the quality limits indicated
in the technical table).
Product functioning changes with the chimney flue
draft and adjustment of the air valve in combustion.
Functioning with initial low draft
To extract air for combustion and discharge the
smoke, the fifi replace needs a draft to be exerted on
the chimney flflue.
If the draft is weak, initially light a “starter” fifi re using
small sized lighting material.
Once the correct draft is restored, you can add the fuel.
As with all the products, the wood product heats and
cools during the various phases. This would lead to
normal dilation. Such dilation can cause slight settling
noise, which is not a reason for dispute.
USER INSTRUCTIONS
FUEL
The product was designed to burn wooden logs or
sawdust briquettes.
Use dry wood logs (max. humidity 20%)Use logs The
use of damp wood would cause the product and the
flue to get dirty, the risk of smoke and a lower yield
than that declared.Each type of wood has different
characteristics that also influence combustion yield.
The data outlined on this manual are with wood used
during certifi cation.
In general wood can have a heat of combustion up to
4.5 kWh/kg while cut fresh it has heat of combustion
around 2 kWh/kg
In general, beech or elm is recommended, or however
class A1 wood according to UNI EN ISO 17225-5
Attention to prolonged use of wood with aromatic oils
(e.g. eucalyptus). Cast iron parts can deteriorate
Use the recommended quantities of wood:
Overloading causes overheating, resulting in damage:
• possible deformation of the inner parts;
• possible irreversible changes to the colour of the
paint on the metal parts for which Edilkamin or the
retailer cannot be held liable.
To respect the environment and safety, do NOT burn,
among other things: plastic, varnished wood, coal and
bark waste.
Do not use the product as an incinerator.
Use of these fuels also nullifi es the guarantee.
First switch on phases
• Ensure you have read and understood the content
of this manual
• Remove all the inflfl ammable parts from the
product (manuals, labels, etc.). In particular
remove any labels from the glass. If they melt, they
would irreversibly damage the glass.
For initial switch on of the fifi replace, always use the
smallest logs. Use larger wooden logs to raise the fifi
re.
Always locate the wood deep in the fifi replace, al-
most in contact with the rear wall, so that even if they
slide they won’t come in contact with the glass.
There may be a slight smell of paint the fi rst few
times it is ignited, however, this will disappear quickly.
Use always the glove supplied to touch
hot parts.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Firebox Riga at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Firebox Riga in the language / languages: English as an attachment in your email.

The manual is 1.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Firebox Riga

Edilkamin Firebox Riga Usermanual and installation guide - English - 80 pages

Edilkamin Firebox Riga User Manual - German - 28 pages

Edilkamin Firebox Riga Usermanual and installation guide - German, French, Italian, Portuguese, Spanish - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info