810842
25
Zoom out
Zoom in
Previous page
1/32
Next page
25
INSTALLER
IMPORTANT! BEFORE PROCEEDING WITH
IGNITION, CAREFULLY READ ALL THE
INSTRUCTIONS AND PRECAUTIONS SHOWN IN
THIS BOOKLET.
First ignition could be difficult because of
the possible presence of air in the gas pipe.
In case of short ignition or switch-off of the
appliance, wait at least 5 minutes before repea-
ting the ignition operation.
When first ignited, the Appliance may give
off a bad smell or vapours. This is entirely
normal. The best thing is to ventilate the premi-
ses adequately.
After igniting, allow the appliance to operate
for about ten minutes at maximum output,
to permit adequate heating.
If the appliance is to be used for short
periods of time, it is best not to switch it off
but rather leave it with the pilot light on. This
way, the formation of condensation is prevented
in the pipes that reach the flue and which, in the
long term could cause hearth corrosion.
REMOTE CONTROL UNIT
Ignition
• Open the gas supply tap.
• Press the switch (5) of the gas valve in “ I “ position.
Make sure the knob (7) of the manual operation
mechanism is positioned on “ON”.
Press the keys OFF and triangle UP of the
remote control at the same time.
An acoustic signal will indicate the start of the start
sequence. The electronic system checks correct gas
flow and ignites the main burner (these operations
could take up to 20 seconds). After burner ignition,
the flame automatically positions on maximum.
If the pilot flame goes out, wait at least five
minutes before repeating the described ope-
ration. During the start phase, the knob of the
manual operation mechanism must be positio-
ned on “ON”.
Operation
Setting the electronic code for RF remote con-
trols (with or without display).
A code is selected automatically between 65000 ran-
dom codes available. The receiver (at the edge of
the chimney) must know the remote control code:
Expected sequence:
- Press and hold the RESET button of the receiver in
the fireplace until you hear two (2) beeps: the first is
short and the second is long. After the second beep,
release the RESET button.
- Within the next 20 seconds, press the button (small
flame) on the remote until you hear two short beeps,
which further confirm the correct setup code. If you
hear one long beep, the acquisition sequence code
failed or the wiring is incorrect.
This setting is performed only once and is
not required after changing the batteries on
the remote or receiver.
Once turned on, you can choose the power level of
the Device using the remote control. Press the remo-
te button "triangle DOWN" to reduce the intensity of
the flame and press "triangle UP" to raise it.
Once the Appliance has been switched on,
the Manufacturer suggests leaving it run-
ning for 10 minutes at max output, before making
any adjustments.
At minimum, the burner remains off, leaving on only
the pilot flame.
From minimum position, the output can be turned up
without repeating the ignition operation.
5
7
1
MAX
OFF
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin EK50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin EK50 in the language / languages: English as an attachment in your email.

The manual is 12.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin EK50

Edilkamin EK50 Usermanual and installation guide - German - 34 pages

Edilkamin EK50 Usermanual and installation guide - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info