Manual Edilkamin Dania Air Tight Plus (page 11 of 60) (English)

810762

Zoom out

Zoom in

1/60

ITALIANO

FLUE SYSTEM

(fumes duct, flue and chimney pot)

This chapter has been drawn up pursuant to European

regulations EN 13384, EN 1443, EN 1856 and EN

1457. The installer must observe both these and any

other local regulations. This manual does not in any

way substitute such regulations.

The product must be connected to a flue system which

ensures that the fumes produced by combustion are

expelled in complete safety.

Before positioning the appliance, the installer must

check that the flue is suitable.

FUMES DUCT, FLUE

The fumes duct (which connects the combustion

chamber smoke outlet with the flue) and the flue itself

must, among other regulatory requirements:

• receive the fumes from a single product (the outlets

of multiple appliances may not be conveyed into

a single flue)

• be routed vertically for the most part

• have no downwards sloping sections

• preferably have a circular internal cross section, or

with a ratio of the sides of less than 1.5

• terminate at roof level with a proper chimney pot:

the flue may not discharge directly on the wall

or into an enclosed space, even if the space in

question is open to the sky

• be made of material with rated fire reaction class

A1 as per UNI EN 13501 or analogous national

regulations

• be certified, with a chimney plate if metal

• be of uniform cross section or vary in cross section

only immediately after the outlet, not at some

midpoint of its length.

THE FUMES DUCT

• Further to the general prescriptions for the fumes

duct and flue, the fumes duct:

• may not be made of flexible metal material

• must be insulated, if routed through unheated

areas or outdoors

• must not be routed through rooms where the

installation of combustion heat generators is

prohibited or there is risk of fire, or that cannot be

inspected

• must enable the recovery of soot and be open for

inspection

• must have a maximum of 3 bends with a maximum

angle of 90°

• if there is a horizontal section, it can have a

maximum length of no more than 3 metres,

depending on the draw. Note, in any case, that

long sections encourage the accumulation of dirt

and are harder to keep clean.

THE FLUE:

Further to the general prescriptions for the smoke duct

and flue, the flue:

• must only be used for discharging fumes

• must be correctly sized to satisfy the requirements

for fume discharging (EN 13384-1)

• should preferably be insulated, in steel with a

circular internal section. If rectangular, the corners

must have a radius of not less than 20 mm, with

aratio of the internal dimensions of <1.5

• must normally be at least 1.5 metres in vertical

length

• must have a constant cross section

• must be waterproof and thermally insulated to

ensure a good draw

• preferably provide a collection chamber for

unburnt residues and condensates

• if pre-existing, must be clean, to prevent fire

hazards

• in general, we recommend fitting a tube inside the

existing masonry chimney if its diameter is greater

than 150 mm.

INSTALLATION

INSTRUCTIONS FOR THE SMOKE

DISCHARGE WITH OR WITHOUT

CONCENTRIC PIPE

INSTALLER

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Dania Air Tight Plus in the language / languages: English as an attachment in your email.

The manual is 2.17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Dania Air Tight Plus

Edilkamin Dania Air Tight Plus Usermanual and installation guide - German - 60 pages

Edilkamin Dania Air Tight Plus Usermanual and installation guide - Dutch - 60 pages

Edilkamin Dania Air Tight Plus User Manual - French - 60 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin Dania Air Tight Plus Manual

Product: