810902
35
Zoom out
Zoom in
Previous page
1/88
Next page
35
ENGLISH
HYDRAULIC CONNECTIONS
The hydraulic connections depend on the type of
system.
However, there are a few “general rules”.
Below are the reference rules according to the Italian
standards:
The plumbing connections must be made by
qualified personnel who can issue documentation
certifying the correct installation according to the
regulations in force in each country (for example,
in Italy pursuant to Ministerial Decree 37/2008
and pursuant to the UNI 10412-2 standard).
The hydraulic system must operate at a pressure
between 1 and 1.5-2 bars at running temperature
(hot) in a closed vessel circuit.
N.B.: the product SHOULD NOT be installed in
place of, for example, an open-vessel installed
cooker without adjusting the expansion system
to closed vessel.
The presence of a puffer (inertial storage
tank) is recommended but not mandatory. Its
advantage is that it releases the product from
“sudden” requests from the system and can be
integrated with other heat sources. It reduces
fuel consumption and increases the efficiency of
the system.
The return temperature of water must be higher
than at least 50–55°C to prevent condensate from
forming. The installer must assess, in relation to
the plant, whether anti-condensate pumps or
valves are required.
An accumulator (tank) is needed to heat low-
temperature radiant panels and must be
installed according to the panel manufacturer’s
instructions. Radiant panels must not receive
water directly from the boiler stove.
The material used in the circuit must be suitable
to withstand overheating.
The safety valve’s relief outlet must be accessible
and visible. Waste water must be conveyed via a
vertical pipe through a funnel with backflow air
vents, at a suitable distance from the point of
drainage.
IT IS FORBIDDEN TO SHUT OFF THE OUTLET
HYDRAULIC INSTALLATION
INSTALLER
All local, national laws and European Standards must
be met in the proper sizing, installation, maintenance
and use of the appliance. Refer to local codes in
each country for installation and for anything not
specifically mentioned.
Any disabling can be made into the installer
parameters.
• C
heck that the hydraulic system has been properly
arranged and that it is equipped with a sufficiently
large expansion vessel for guaranteeing its safety.
The presence of the vessel incorporated in the
boiler stove does NOT guarantee adequate
protection against thermal expansion of the water
in the entire system. Therefore, installers should
assess whether an additional expansion tank is
needed, depending on the type of system.
The installer must assess, on the basis of the type
of water and system, whether water conditioners
are required pursuant to the UNI 8065 standard
(water treatment in heating systems for civil use).
Direct plumbing to the radiators prevents proper
operation, owing to the small diameter of their
pipes.
Fill the system via the filling valve (we recommend not
exceeding a pressure of 1.5 bar).
During the filling phase, bleed the pump and the relief
valve.
Pressure gauge
The boiler stove has an electronic system for reading
the water pressure. There is no analogue pressure
gauge. The water pressure is shown on the display, in
the middle as shown in the diagram below.
M®Ä
T«
14,9°C
18:02
20
1,2 bar
The return water temperature must be at
least 50-55° C to avoid condensation. An
anti-condensation system is essential,
under penalty of forfeiture of warranty,
as installation is not correct and non-
compliant.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Blade H 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Blade H 15 in the language / languages: English as an attachment in your email.

The manual is 4.2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Blade H 15

Edilkamin Blade H 15 Usermanual and installation guide - German - 88 pages

Edilkamin Blade H 15 Usermanual and installation guide - French - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info