663874

EdgeCraft Chef-s Choice - Professional 325 Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
6
INSTRUCTIONS
Read This Before You Start to Sharpen
The Chef’sChoice® Model 325 sharpener is designed to sharpen either Straight edge or
Serrated edge blades.
1. Sharpen Serrated Blades Only in Stage 2. Do not sharpen serrated blades in Stage 1
until you read the section titled Procedure for Sharpening Serrated Blades.
2. Straight Edge Blades are sharpened in Stages 1 and 2. Start in Stage 1 if the knife
is being sharpened for the first time or if the knife is very dull. See following Section for
more details.
Procedure for Sharpening Straight Edge Blades
Straight Edge Blades: Sharpening First Time
Before you turn on the power, slip a knife blade smoothly into the slot between the left
angle guide of Stage 1 and the elastomeric spring. Do not twist the knife. (See Figure 3.)
Move the blade down in the slot until you feel it contact the diamond disk. Pull it towards
you, lifting the handle slightly as you approach the tip. This will give you a feel for the
spring tension. Remove the knife and press the Power Switch. A red “indicator” on the
switch appears when this switch is turned “ON.”
Stage 1: If you are sharpening a straight-edge knife for the first time, start in Stage 1. Pull
the knife once through the left slot of Stage 1 (Figure 3) by slipping the blade between
the left angle guide and the polymeric spring while pulling the blade toward you and
simultaneously moving the blade downward in the slot until it engages the diamond coated
disk. You will hear it make contact with the disk. Insert the blade as close as possible to its
bolster or handle. If the blade is curved, lift the handle slightly as you sharpen near the tip
of the knife, keeping the blade edge approximately parallel to the table. Sharpen the entire
blade length. For an eight (8) inch blade each pull should take about 5 seconds. Pull shorter
blades through in 2-3 seconds and longer blades in 6 seconds. Next, repeat with one full
length pull in the right slot of Stage 1.
Figure 4. Inserting blade in right slot of Stage 1.Figure 3. Stage 1. Inserting blade in slot between
guide and elastomeric spring. Alternate individual
pulls in left and right slots.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - Professional 325 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - Professional 325 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info