663875
6
Zoom out
Zoom in
Previous page
1/12
Next page
6
instructions
rEaD this BEForE You start to sharPEn
The Chef’sChoice
®
EdgeSelect-Pro
Diamond Hone
®
Knife Sharpener Model 125 is designed
to sharpen either Straight edge or Serrated edge blades.
1. Sharpen Serrated Edge Blades only in Stage 3. Do not sharpen serrated blades in
Stages 1 and 2, as that will tend to remove more metal than necessary from the serrations.
See Section titled Procedure for Sharpening Serrated Blades for more details.
2. Straight Edge Blades can be sharpened in all three stages, however, use of Stage 1 may
be necessary only if the knife is very dull or if you wish to create an edge with extra “bite”.
See following Section for more details.
ProcEDurE For sharPEninG straiGht EDGE BlaDEs
straiGht EDGE BlaDEs: sharPEninG First timE
Before you turn on the power, remove the cover positioned over Stage 1 and slip a knife blade
smoothly into the slot between the left angle guide of Stage 1 and the elastomeric spring.
Do not twist the knife. (See Figure 3.) (Retain the Stage 1 cover as a ready reminder of the
sharpening steps.)
Move the blade down in the slot until you feel it contact the diamond disk. Pull it towards you,
lifting the handle slightly as you approach the tip. This will give you a feel for the spring tension.
Remove the knife and press the Power Switch. A red “indicator” on the switch appears when this
switch is turned “ON.”
Stage 1: (If your knife is already reasonably sharp, skip Stage 1 and go directly to Stage 2.) If you
are sharpening a knife for the first time, if the knife is very dull or if the knife has been sharpened
with a sharpening steel, start in Stage 1. Pull the knife once through the left slot of Stage 1 (Figure
3) by slipping the blade between the left angle guide and the polymeric spring while pulling the
blade toward you and simultaneously moving the blade downward in the slot until it engages
the diamond coated disk. You will hear it make contact with the disk. Insert the blade as close as
possible to its bolster or handle. If the blade is curved, lift the handle slightly as you sharpen near
the tip of the knife, keeping the blade edge approximately parallel to the table. Sharpen the entire
blade length. For an eight (8) inch blade, each pull should take about 4 seconds. Pull shorter blades
through in 2-3 seconds and longer blades in 6 seconds. Next, repeat with one full length pull in
the right slot of Stage 1.
Note: Each time you insert the blade you should simultaneously pull the blade toward you. Never
push the blade away from you. Apply just enough downward pressure to make contact with the
wheel - added pressure does not modify or speed the sharpening process.
Figure 3. Stage 1. Inserting blade in slot between guide
and elastomeric spring. Alternate left and right slots.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - EdgeSelect-Pro 125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - EdgeSelect-Pro 125 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info