663885

EdgeCraft Chef-s Choice - Angle Select 1520 Manual

15
Zoom out
Zoom in
Previous page
1/16
Next page
15
you from inserting the blade so far that the choil area will catch on the front stop-bar of the
sharpener as you withdraw the blade. A little practice will help you perfect this technique. As
you insert the blade let your finger slide down the front of the sharpener.
9. Used correctly, you will find you can sharpen the entire blade to within 1/8” of the bolster or
the sharpener handle. This is a major advantage of the Chef’sChoice
®
Model 1520 compared
to other sharpening methods—especially important when sharpening chef’s knives where
you need to sharpen the entire blade length in order to maintain the curvature of the edge
line. If your chef’s knives have a heavy, thick bolster near the handle extending to the edge,
a commercial grinder can modify or remove the lower portion of the bolster so it will not
interfere with the sharpening action, allowing you to sharpen the entire blade length.
10. The stropping/polishing disks in Stage 3 are designed to last for years of use, however
you can maximize their useful life by periodically modifying your sharpening pattern in the
preceeding Stage used. The burr developed in the preceeding Stage will mildly wear the
stropping/polishing disk it first contacts in Stage 3. Vary your last pull in the preceeding
Stage (Stage 1 or Stage 2) by sometimes making the last pull on the left disk and at other
times finish on the right disk of that Stage.
11. Do not attempt to use this sharpener to sharpen either ceramic knives or scissors.
NORMAL MAINTENANCE
No lubrication is required for any moving parts, motor, bearings, or sharpening surfaces. There
is no need for water on abrasives. The exterior of the sharpener may be cleaned by carefully
wiping with a damp cloth. Do not use detergents or abrasives
Once a year or so as needed you should remove metal dust that will accumulate inside the
sharpener from repeated sharpenings. Remove the small rectangular clean-out cover (Figure
18) that covers an opening on the underside of the sharpener. You will find metal particles
adhered to a magnet attached to the inside of that cover. Simply rub off or brush off accumulated
filings from the magnet with a paper towel or tooth brush and reinsert the cover in the opening.
If larger amounts of metal or other dust have been created you can shake out any remaining
dust through the bottom opening when the cover is removed. After cleaning, replace the cover
securely with its magnet in place.
Figure 18. Removing cover under base to clean out
metal dust (See Normal Maintenance section).
… 15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - Angle Select 1520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - Angle Select 1520 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info