663885

EdgeCraft Chef-s Choice - Angle Select 1520 Manual

12
Zoom out
Zoom in
Previous page
1/16
Next page
12
STEP 2: STROPPING/POLISHING, STAGE 3
In Stage 3 make three (3) to four (4) pairs of slow pulls each about 4 seconds, alternating in the
left and right slots.
Follow this, still in Stage 3, with three (3) pairs of faster pulls each about 1-2 seconds, alternating
in the left and right slots. There should not be a noticeable burr along the edge. Test blade for
sharpness. It should be incredibly sharp. If not sharp repeat this Step 2.
RESHARPENING EUROPEAN/AMERICAN KNIVES
Re-sharpen the European/American knives whenever practical using just Stage 3 following the
instructions (Step 2) above. When that fails to quickly re-sharpen, return to Stage 2 and make
two or three pairs of alternating pulls. Check for a burr along the edge and when a burr exists
proceed again to Stage 3 following the instructions in the preceding section.
CONVERTING EUROPEAN/AMERICAN KNIFE EDGE
TO 15 DEGREE ASIAN STYLE EDGE
With the Model 1520 you can convert any European or American style knives that are used
primarily for light duty work to the 15 degree Asian edge. For example you might consider
converting light duty paring knives and thin utility blades to 15 degrees. To make this conversion
follow the Instructions for Sharpening Asian Blades, pages 7 to 9. Initial sharpening in Stage 1
will take longer than you might expect but subsequent resharpening time will be normal.
PROCEDURE FOR SHARPENING SERRATED BLADES
Serrated blades are similar to saw blades with scalloped depressions and a series of pointed
teeth. In normal use the pointed teeth do most of the cutting.
Serrated blades of all types can be sharpened in the Chef’sChoice
®
Model 1520. However, use
only Stage 3 (Figure 14) which will sharpen the teeth of the serrations and develop microblades
Figure 13. Honing in Stage 2 (left slot). European and
American style blade.
Figure 14. Use only Stage 3 for sharpening
serrated knives.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - Angle Select 1520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - Angle Select 1520 in the language / languages: English as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info