Manual Edesa HC-60 (page 7 of 25) (English, German, French, Italian, Spanish)

500014

Zoom out

Zoom in

1/25

Part 1 Installation

ELECTRIC FAN ASSISTED OVEN

General instructions

Connection to the mains

The appliance referred to in this manual has been

manufactured in conformity to the following directives:

73/23/EEC, 93/68/EEC “Low Voltage”; 89/336/

EEC, 92/31/EEC, 93/68/EEC “Electromagnetic

Compatibility".

The appliance shall be installed by a qualified

technician according to the regulations and directives in

force in the country where it is installed, as well as the

instructions in this manual. The appliance shall be used

exclusively by trained personnel and only for the purpose

for which it has been designed. The appliance should

be checked once a year by a qualified technician.

Remove the packaging from the appliance as well

as the protective plastic sheet, and, if necessary,

remove traces of glue with a suitable solvent. To

dispose of the packaging, follow local directives.

The technical specifications of the appliance can be

found on the data plate attached to the back panel.

When installing the appliance, all the regulations

in force shall be observed, such as:

Before connecting the appliance to the mains,

compare the electrical set-up data on the data plate

to the characteristics of the local electrical energy

supply.

Adjust the height of the appliance by regulating

the feet, and make sure that it is perfectly level.

The appliance is equipped with a connecting cable

to which the installer must connect a circuit breaker

which cuts off the flow of electricity in all poles; the

distance between the open contacts must be at least

3 mm. The circuit breaker must be easy to reach.

The cable must not be placed near heat sources.

The area around the cable must not have a temperature

above 50° C. If the cable must ever be replaced,

consult the wiring diagram attached. The electric

supply cable must not have specifications inferior to

type H07 RN-F. It must have a cross-sectional area of

at least 3x1.5 mm

To reach terminal board “M”, remove the panel

located at the back of the appliance. Disconnect the

terminal board conductors, loosen the cable clamp,

and replace the cable following the procedure

inversely.

It is absolutely necessary to earth the appliance.

For this purpose, there is a screw marked with the

symbol near the terminal board to which the

earthing conductor must be connected.

The appliance must also be connected to a

unipotential earthing circuit. This connection can be

made using the screw marked with the symbol ,

located below the appliance near the right rear foot.

• all applicable national laws in force;

• all regional or local regulations, such as building

codes;

• directives and regulations of the local electrical

supplier company;

• accident prevention regulations in force;

• fire prevention regulations;

• applicable I.E.C. regulations.

The appliance should be installed under

a hood for the removal of cooking fumes.

If the appliance is installed near walls, panels or

kitchen furniture, etc., they must be made of fire-proof

material; if they are not, they must be protected with

fire-proof material which insulates from heat.

GB IE

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edesa HC-60 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edesa HC-60 Manual

Product: