Manual Economy ebf 18k cdm 1072 (page 7 of 28) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388699

Zoom out

Zoom in

1/28

Ferm 07

• As soon as the green trickle charging lamp

(13) lights up, charging has been completed

and the device is ready for operation.

Only use the charger in a dry

environment at temperatures

between 5˚C and 40˚C.

The battery in your drill was not charged up at

the factory. Before using it for the first time, you

should charge it for approx. 1 – 2 hours so that it

reaches full capacity. The final capacity of the

battery is reached after 4 – 5 battery cycles.

Discharging the battery

Not only charging batteries is important,

discharging is of equal importance or

even greater importance.

• When the battery is charged the cordless drill

has to be used until you start noticing that the

power of the drill is diminishing and that the

maximum rotational speed is not reached.

• The battery is almost discharged now. Only

now you can start charging the battery.

• Charging the battery while it is still charged for

say one-third of capacity, the so-called

‘memory effect’ can occur. Since during

charging only the discharged part of the

battery capacity of the battery is being

charged now, the battery can start crystallizing

in the one-third that is still charged. This part

of the battery capacity can never be used

afterwards.

• Do not discharge the battery to the minimum.

As soon as you notice that the power or the

maximum rotational speed is diminishing, you

have to charge the battery. When you proceed

using the drill and the battery becomes fully

discharged, the so-called ‘switch of poles

effect’ can occur. The polarity of the battery

poles will be switched: the ‘+’will become ‘-‘

and the ‘-‘ will become the ‘+’. Once this has

occurred the polarity will remain switched

during loading and this will damage the

battery irreparable.

When the cordless drill is not being

used over a longer period of time, the

battery has to be charged fully first. The

battery has to be stored in charged

condition.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine.

Regularly clean the machine housing with a soft

cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt.

If the dirt does not come off use a soft cloth

moistened with soapy water. Never use solvents

such as petrol, alcohol, ammonia water, etc.

These solvents may damage the plastic parts.

Lubrication

The machine requiers no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. In the back of this manual you find

an exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging. NiCd cells are recyclable.

Faulty and/or discarded electrical or

electronic apparatus have to be

collected at the appropriate recycling

locations.

Warranty

The guarantee conditions can be found on the

separately enclosed guarantee card.

50 Ferm

Indstilling af drejningsmoment

Fig. D

Maskinen har 16 forskellige indstillinger for

drejningsmoment til regulering af den kraft

hvormed skruer bliver skruet i eller ud.

• Sæt indstillingsringen for drejningsmoment (2)

i den ønskede position.

De indstillinger af drejningsmomentet der er til

rådighed, vises på indstillingsringen dels med

cifrene fra 1 til 8, dels med prikker mellem

cifrene som angiver mellempositioner (dvs. i

alt 16).

• Man skal helst vælge den laveste position der

giver tilstrækkelig kraft til at dreje skruen

rundt. Vælg en højere position hvis motoren

"glider i koblingen".

Anvendelse som skruetrækker.

• Sæt knappen for omløbsretningen (5) i

position 'R' for at skrue skruer i.

• Sæt knappen for omløbsretningen (5) i

position 'L' for at skrue skruer ud.

Boring

• Drej indstillingsringen for drejningsmoment (2)

i boreposition.

Sørg for at knappen for

omløbsretningen (5) altid står i position

'R' når du borer.

Start og stop

Fig. A

• Tryk på startknappen (1). Du kan regulere

maskinens omdrejningstal ved at trykke mere

eller mindre hårdt på knappen.

• Når du slipper startknappen (1), bliver

patronen straks bremset, og der er ikke noget

efterløb.

• Når maskinen er slukket, kan du blokere den

ved at sætte knappen for omløbsretningen (5)

i den midterste position.

Læg først maskinen fra dig når motoren står helt

stille. Læg ikke maskinen på et støvet underlag.

Der kan trænge støv ind i mekanismen.

Opladning af batterier

Fig. E

• Sæt batteriet (5) i opladeren (11) som vist på

tegningen. Vær opmærksom på markeringen

af polerne + og -.

• Sæt opladerens stik i stikdåsen. Nu lyser

den røde kontrollampe for hurtigladning (12).

• Så snart den grønne kontrollampe for

vedligeholdende (13) opladning lyser, er

opladningen færdig. Batteriet er driftsklart.

Opladeren må udelukkende anvendes i

tørre omgivelser og ved temperaturer

mellem 5 °C og 40 °C.

Batteriet til din boremaskine er ikke opladet ved

leveringen. Før det tages i brug første gang, er

det nødvendigt at oplade det i ca. 1-2 timer for at

nå op på fuld effekt. Batteriets endelige kapacitet

opnås efter 4-5 op- og afladningscyklusser.

Afladning af batteriet

Det er ikke kun opladningen af

batterierne, der er vigtig, afladningen

har lige så stor eller måske endnu

større betydning.

• Når batteriet er opladet, skal akku-

boremaskinen bruges, indtil du begynder at

lægge mærke til, at boremaskinens kraft er i

aftagende, og at den ikke når op på den

maksimale omdrejningshastighed.

• Batteriet er nu næsten afladet. Først nu kan

du begynde at lade batteriet op.

• Hvis batteriet oplades, mens det stadig er

opladet til f.eks. en tredjedel af kapaciteten,

kan den såkaldte ‘hukommelseseffekt’

forekomme. Da det under opladningen nu kun

er den afladede del af batteriets

batterikapacitet, der oplades, kan batteriet

begynde at krystallisere i den tredjedel, der

stadig er opladet. Denne del af

batterikapaciteten kan aldrig bruges bagefter.

• Aflad ikke batteriet til minimum. Så snart du

bemærker, at styrken eller den maksimale

omdrejningshastighed begynder at tage af,

skal batteriet oplades.

Når du fortsætter med at bruge boret, og

batteriet bliver helt afladet, kan den såkaldte

‘ombyttede poler’-effekt forekomme.

Batteripolernes polaritet bliver byttet om: ‘+’

bliver til ‘-‘ og ‘-‘ bliver til ‘+’. Er dette først

sket, vil polariteten stadig være byttet om

under opladningen, og dette vil skade batteriet

uopretteligt.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Economy ebf 18k cdm 1072 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 19,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Economy ebf 18k cdm 1072 Manual

Product: