742223

Ecoforest Eco III Manual

30
Zoom out
Zoom in
Previous page
1/152
Next page
29
1. PLEASE BEWARE THAT...
In order to prevent the risk of accident, a correct installation must be done following the instructions of this
manual. Your ECOFOREST distributor will be available to help you and provide you information related to codes,
assembly and installation norms in your area.
As ecoforest do not have direct control on the installation of your stove, ecoforest do not guarantee it and do
not bear the responsibility of any damage that could result from a bad use or a bad installation.
We carefully recommend the heat calculation to be made by a qualified heating engineer.
We recommend that a confirmed specialist sets up your pellets stove.
Maintenance work to be carried out at the end of the season or for every 500 kg of fuel burned, as well as
any repairs or equipment modifications, must be performed by authorized personnel.
Before getting started with the stove installation, please check section 4.
2. ADVICE AND RECOMMENDATIONS.
2.1. All local regulations, including those referring to national and European standards must be met when
installing the stove.
2.2. The stove must be installed on floors of sufficient bearing capacity and, if the existing construction does not
allow this, the floor must be adapted and made suitable, for example by fitting a load distribution plate.
2.3. Never use petrol, fuel for lanterns, kerosene nor any similar liquid. Keep this kind of fuel away from your
stove.
2.4. Do not try to turn on your stove if some glass is broken.
2.5. Make sure the glass door of the fireplace is well closed while the stove is in operation; also check the
cleaning hatches (if you have touched them).
2.6. Unauthorized modifications are forbidden. Use only spare parts provided by Ecoforest (see exploded view).
2.7. Do not overload the stove; continuous heating efforts might cause premature aging and damage paint (it is
recommended not to exceed 250°C for gas outlet temperature).
2.8. Do not use the stove as a burner.
2.9. To prevent possible electrical shocks, only trained personnel should have access to the sides and the back of
the stove.
2.10. For the Córdoba, Granada and Praga stove models, the air-convection trim cover must be placed at an angle
of 50° (as far as it will go) with respect to the frame, whenever the stove is operational.
Drawing 1
2.11. In order to refill the stove with fuel, the user must open the hopper lid and empty the contents of the fuel
tank carefully, to prevent it from overflowing. See drawing 2 (ECO III).
The fuel loader for the models Córdoba (drawing 3) and Córdoba Glass, Teide and Granada, is removed from
the loading tray by pulling on the handle which is located on the air-convection trim cover. Always load fuel
when the device is cold.
Drawing 2

Air
-
convection trim cover
.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ecoforest Eco III at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ecoforest Eco III in the language / languages: English, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 9,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info