581259
6
Zoom out
Zoom in
Previous page
1/15
Next page
Pulsports-300/400
Pulsports-300/400
E10- -E11
HEART RATE FUNCTION
DESCRIPTIONS
1.Start /Stop heart rate measure function
1. Press P.MODE for 2 seconds to start heart rate measurement
function.
2. When the function is operating, the LCD will display the signal as
” and “ ”.
3. Press P.MODE for 2 seconds to stop heart rate measurement
function.
4. If a signal is not received for 5 minutes, the function will turn off
automatically.
2. Start/Stop heart rate data record function
1. Press ST/SP to start heart rate measurement function.
2. Press P.MODE to switch to EXE_TM function.
3. Press ST/SP, the signal shown as ” ” at the top right of the
display will change to “ , and this means the data record
function is started. Stop by pressing ST/SP, the signal will change
to “ “.
4. AVG, STW, CAL, EXE.TM, WT.LOS, FT.LOS, MAX, IN.TM,
OVR.TM, T_FT.L and T_CAL functions will only work while the
record function is on.
5. CAL/H and %FAT Loss will be displayed automatically when heart
rate is measured. The value will become “--“ while no pulse is
detected.
6. CAL, CAL/H, WT.LOS, %FAT Loss, FT.LOS and T_FT.L mode will
be calculated when the heart rate is equal or over 90 bpm.
3. Reset heart rate record data
1. Press P.MODE to switch to EXE_TM mode.
2. Press T.MODE for 2 seconds to clear the record.
3. T_CAL and T_F T. L record can only be erased under the original
function mode.
4. Heart rate display descriptions
1. Intensity = Current heart rate/Maximum heart rate.
2. Range of heart rate measurement is from 40 bpm to 240 bpm.
5. Program target zone mode (3 modes option)
Setup the target zone by entering the percentage of maximum heart
rate for the following 3 modes. Maximum heart rate based on the
data you input.
PRG
1. There are 3 mode of programmable target zones setup:
a). H: Switch the Target Zone manually.
b). T: Switch the Target Zone automatically according to the setup
time (0-99 minutes) for each zone; program will jump to the
next zone when the timer for the current zone is complete.
c). E: Switch the Target Zone automatically according to the setup
exercise time (0-99 minutes) for each zone; program will
jump to the next zone when the exercise time for the
current zone is complete.
2. The Beep alarm will sound when the target zone shifts from one
zone to another in auto-shift mode. It will beep for 10 seconds
when all target zones are complete, and END will be displayed.
3. In any zone, press T.MODE for 2 seconds for restart from the first
zone.
4. “ “ will display when the heart rate within the target zone.
5. ” “ will display when the heart rate is below the lower limit of the
target zone. (Beep should sound).
6. “ “ will display while the heart rate is above the upper limit of
target zone. (Beep should sound).
7.
a). Press P.MODE to select “PRG” mode.
Target zone program setting:
b). Press SET for 2 seconds to enter program target zone setting
mode.
c). Press T.MODE or ST/SP to choose the type of program.
d). Refer the Data Setting Processes
6. Stop watch mode
to adjust the Target zone
data. (Refer Fig .D)
1. Calculation of exercise time only works while a heart rate is
detected.
STW
2. The range is from 0 hr. 00 min. 00sec. to 99 hr. 59 min. 59 sec.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Echowell OPAL-300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Echowell OPAL-300 in the language / languages: English as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Echowell OPAL-300

Echowell OPAL-300 User Manual - Dutch - 16 pages

Echowell OPAL-300 User Manual - French - 15 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info