424459
8
Zoom out
Zoom in
Previous page
1/48
Next page
Quick Reference Guide
Page 2 EchoStar International Corporation
© 2004 EchoStar International Corporation
All rights reserved
2. TO INSTALL THE RECEIVER
For the location and availability of the basic front panel controls, please refer to the front panel as
shown on the packaging. If available, the basic front panel controls are:
For the location and availability of the connectors, please refer to the rear panel as shown on the
packaging. If available, the connectors on the rear panel are:
WARNING
ALL EQUIPMENT INVOLVED IN THE INSTALLATION TASK MUST BE INSTALLED CORRECTLY AND SWITCHED
OFF. MAKE SURE THAT IT IS SAFE TO PROCEED WITH THE INSTALLATION TASK.
U
NSAFE CIRCUITS AND INSTALLATIONS CAN CAUSE (SERIOUS) INJURY OR DAMAGE TO EQUIPMENT.
The standby/on button, to switch the receiver to Standby or On.
Note that the ON/OFF switch is located on the rear panel.
The arrow up button, to move one channel up (live only).
The arrow down button, to move one channel down.
Indicators The red indicator shows that there is sufficient signal received
The orange indicator shows that the receiver is in standby
The green indicator shows that the receiver is set to on.
LNB IN (F-type), to connect a dish installation;
IF OUT (F-type), for a loop through connection to another receiver/decoder.
(Yellow) VIDEO (RCA), to connect to the composite video input of the TV (monitor).
(White) AUDIO L (RCA), to connect to the left audio input of a stereo set.
(Red) AUDIO R (RCA), to connect to the right audio input of a stereo set.
(Black) S/PDIF (RCA), to connect to a Dolby Digital (AC-3) compatible audio equipment.
TV (SCART), to connect to a TV with a fully-featured SCART cable;
VCR (SCART), to connect to a VCR with a fully-featured SCART cable.
SVHS (DIN), to connect to a S-Video input of SVHS compatible equipment.
ANT IN (IEC), to connect to a VHF/UHF terrestrial TV antenna;
TV OUT (IEC), to connect to the UHF connector of a TV or a VCR.
RS-232 (sub-D), to connect to the serial communication port of a PC.
ON/OFF switch, to switch the receiver ON or OFF.
3. FIRST TIME INSTALLATION
1. Make sure, all connections are made safely.
2. Switch the receiver to ON and wait for the
Languages menu to appear.
3. For detailed information about the pre-
programmed channel lists and installation
types, please refer to the appendix.
4. When in the Pre-programmed lists, select a
language and the related pre-programmed
channel list.
5. Make sure, the pre-programmed language
settings are convenient for you.
6. Select Continue and press the OK key.
7. Allow the receiver some time to load the
channel list and wait fo the live video to
appear.
8. If live video does not appear, please refer to
the Getting started section for further
instructions (DiSEqC1.2, USALS).
CAUTION
Tighten the cable connectors only by hand.
Do not use any tools. You will damage the
connector pins if you over tighten the
connector. This will result in loss of signal
quality, or even total loss of reception.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Echostar dsb 890 2ci at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Echostar dsb 890 2ci in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info