645375
26
Zoom out
Zoom in
Previous page
1/40
Next page
26
CS-310
CARBURETOR ADJUSTMENT
Every unit is run at the factory and the carburetor
is set in compliance with Emission Regulations. In
addition, the carburetor is equipped with “H” (High
Speed) and “L” (Low Speed) needle adjustment
limiters that prevent settings outside acceptable
limits.
1. Before adjusting carburetor clean or replace air
lter and mufer “Spark Arrestor Screen”.
2. Make sure the bar and chain are properly ad-
justed.
3. Start engine and run several minutes to bring to
operating temperature. Flash choke twice during
warm-up to clear any air from the fuel system.
4. Stop engine.
Turn “H” speed needle counterclockwise (CCW)
to stop.
Turn “L” speed needle midway between full
clockwise (CW) stop and CCW stop.
5. Idle Speed Adjustment:
Start engine, turn “Idle” speed adjustment
screw CW until the saw chain begins to turn,
then turn screw out CCW until the saw chain
stops turning.
Turn screw out, CCW, an additional 1/4 turn.
6. Accelerate to full throttle for 2 - 3 seconds to
clear any excess fuel in the engine, then return
to idle.
Accelerate engine to full throttle to check for
smooth transition from idle to high speed.
If engine hesitates turn “L” needle CCW 1/8 turn
and repeat acceleration.
Continue adjustment until smooth acceleration
results.
7. Check idle speed and reset if necessary as
described in item 5. If a tachometer is available
idle speed should be set to 3200 r/min.
WARNING
Cutting attachment must not move when unit is
idling.
CAUTION
When starting, idling adjustment speed should
be adjusted not to rotate the saw chain.
Correct idle speed is adjusted 3,200 r/min. or
1/4 turn CCW from the point the chain stops
moving.
When you experience trouble with the
carburetor, contact your dealer.
Idle adjusting screw
Low speed needle (L)
High speed needle
(H)
High Altitude Operation
Thisenginehasbeenfactoryadjustedtomaintain
satisfactorystarting,emission,anddurability
performanceupto1100feetabovesealevel(ASL)
(96.0kPa).Tomaintainproperengineoperation
andemissioncomplianceabove1100feetASLthe
carburetormayneedtobeadjustedbyanauthorized
ECHOservicedealer.
IMPORTANT
If the engine is adjusted for operation above
1100 feet ASL, the carburetor must be
readjusted when operating the engine below
1100 feet ASL, otherwise severe engine damage
may result.
Engine Break-In
New engines must be operated a minimum dura-
tion of two tanks of fuel break-in before carbure-
tor adjustments can be made. During the break-in
period your engine performance will increase and
exhaust emissions will stabilize. Idle speed can
be adjusted as required.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Echo CS-310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Echo CS-310 in the language / languages: English as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info